03-22-2012
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hello all,
instead of type pwd everytime to find down where I am at. is there a command set prompt to put in to your profile on shell so it invisible every you type cd?
thanks in advance... (3 Replies)
Discussion started by: phapvn
3 Replies
2. UNIX for Dummies Questions & Answers
Hello,
I feel a little initimidated to ask this question, but ... where am I able to find the font path (Solaris 8)?
Bye Sysadv (1 Reply)
Discussion started by: sysadv
1 Replies
3. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
4. Shell Programming and Scripting
Im trying to setup my profile to export the PATH at login
i had this in my .bashrc
export PATH=/usr/local/bin:/usr/bin/
however when i login and type echo $PATH i only get
bash-2.05$ echo $PATH
/usr/bin:
any ideas on what im doing wrong?
ive used linux for years but this is my... (1 Reply)
Discussion started by: recklessop
1 Replies
5. HP-UX
Hi All,
I am trying to make a Boot from San setup on 11.31 IA64 (rx2660). The San array I am using is EMC Clariion with failover mode ALUA.
Now, My setup is ready and I am able to boot my host from the Lun. I have 4 paths to my Lun from my host. Question is how do I add the entries in EFI... (0 Replies)
Discussion started by: barun agarwal
0 Replies
6. Solaris
Hi all ,
I am trying to isntallsolaris 10 using a DVD , But when i try to boot from the OB Prompt i am getting this error :
Rebooting with command: boot cdrom -install
Boot device: /pci@1f,700000/pci@0/pci@1/pci@0/ide@1f/cdrom@0,0:f File and args: -install
Can't read disk label.
Can't open... (2 Replies)
Discussion started by: ppass
2 Replies
7. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
8. Solaris
Hi,
I have an Oracle/Sun T3-2 Server with a duel SAS controller Fujitsu DX60 array attached.
I have 2 x SAS HBA's in the T3-2. One HBA cabled to CM0 and one HBA cabled to CM1 of the array.
The array is setup with one RAID GROUP and one VOLUME and one LUN
In Solaris I can see one device... (4 Replies)
Discussion started by: general_lee
4 Replies
9. Solaris
Hi,
I am running into a some problems creating a dual boot system of 2 solaris instances using ZFS file system and I was wondering if someone can help me out.
First some back ground. I have been asked to change the file system of our server from UFS to ZFS. Currently we are using Solaris... (3 Replies)
Discussion started by: estammis
3 Replies
10. Solaris
Hello,
I have a problem with my machine that won't boot properly.
The story is that I installed a software called apcupsd, which is a control application for my APC battery UPS. I have used version 3.14.10 earlier, but as part of restoring my previously crashed os harddrive I wanted to... (18 Replies)
Discussion started by: Zorken
18 Replies
LEARN ABOUT NETBSD
urlphy
URL(4) BSD Kernel Interfaces Manual URL(4)
NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8)
HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
September 18, 2006 BSD