10-20-2011
Thanks but afraid that didn't work either, here's my config:
HWADDR=00:21:9B:0E:C7:4D
TYPE=Ethernet
BOOTPROTO=none
IPADDR0=192.168.1.10
PREFIX0=24
GATEWAY0=192.168.1.254
DNS1=192.168.1.254
DEFROUTE=yes
IPV4_FAILURE_FATAL=yes
IPV6INIT=no
NAME="Wired connection 1"
UUID=90bf39e6-4141-4839-a978-6156ba608ac0
ONBOOT=yes
ETHTOOL_OPTS="speed 100 duplex full autoneg off"
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi there! I tried to search for something like this here but couldn't find anything. I need to run a specific program when linux starts up. I need to run it after the rp-pppoe has started because this prog needs internet connection.
I start the program by entering ./dynix start (its in my home... (4 Replies)
Discussion started by: D-Lexy
4 Replies
2. Filesystems, Disks and Memory
How can I compile a code that can be runned on boot:?? (2 Replies)
Discussion started by: d4n1l0d
2 Replies
3. Ubuntu
I have two systems in my computer . I update the ubuntu system these days and always interrupt it and exit the system . now the system cannot boot after Running local boot scripts(/etc/rc.local), it just stops there. i have to terminate the gnome display manager. what can i do with it ? thank... (0 Replies)
Discussion started by: tcb3210
0 Replies
4. Solaris
Hi,
i have a script which need to do behave differently when run as a startup process from init.d/ rc2.d script and when run manually from shell.
How do i distinguish whether my script is run by init process or by shell??
Will the command
/proc/$$/psinfo | grep "myscript" work well???... (2 Replies)
Discussion started by: vickylife
2 Replies
5. Shell Programming and Scripting
Hi,
I am uising Suse linux on my system and i tried :
man ethtool and i got the manual for ethtool but when i tried to use the command as:
ethtool -a eth0
it says Command not found.
also, i tried rpm -qa|grep ethtool i got:
ethtool-3-15.2 so,it means my system has ethtool server or... (4 Replies)
Discussion started by: salil2012
4 Replies
6. Programming
Hi,
I'm using ethtool to change network settings:
Just for the experiment, i want to change speed to 10, instead of 100,
I type:
ethtool -s eth0 speed 10 duplex full autoneg off
and to view settings i type:
ethtool eth0, and get this:
Settings for eth0:
Supported ports:
... (4 Replies)
Discussion started by: alex889
4 Replies
7. UNIX for Dummies Questions & Answers
dears
am having solaris 10, and i would like to know if the NTP service is running when the OS staritng?on the other hand how can i make it start at the boot up?note the ntp is managed by the SMF in solaris 10.
thanks a lot (2 Replies)
Discussion started by: thehero
2 Replies
8. Shell Programming and Scripting
I am using blow script :--
#!/bin/bash
FIND=$(ps -elf | grep "snmp_trap.sh" | grep -v grep) #check snmp_trap.sh is running or not
if
then
# echo "process found"
exit 0;
else
echo "process not found"
exec /home/Ketan_r /snmp_trap.sh 2>&1 & disown -h ... (1 Reply)
Discussion started by: ketanraut
1 Replies
9. Red Hat
Dear community, as already done tons of times, I prepare the RedHat installation on VMWare, then clone it with clonezilla, and finally restore it on final server. Due to different hrdware, I have to boot from rhel-server-7.4-x86_64-boot.iso cd and rewrite the initramfs that contains the hardware... (3 Replies)
Discussion started by: Lord Spectre
3 Replies
10. UNIX for Beginners Questions & Answers
Hi All,
I am trying to find my NIC card speed in centos 5. But i am unable to get the info using ethtool command.
# ethtool eth0
Settings for eth0:
Link detected: yes
and even tried to look for the file # cd /sys/class/net/eth0/speed files which is also not available.... (8 Replies)
Discussion started by: sravani25
8 Replies
LEARN ABOUT SUSE
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)
NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <erezz@voltaire.com>.
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)