10-20-2011
The grub online docs will pave the way. If you got into grub, it's a good thing. You just have to ask grub to find the kernels that are installed and it will find them. Reply if you are still stumped after some research and trial-error
9 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
2. SCO
hi...
i hav a problem to install sco unix
while installing sco unix 5.0.5 in acer altos with hardware raid
am getting error
"Warning HD: no root disk controller was found
system error 5: while getting fs type
flushing controller: DAC960PRL cache done."
i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies
3. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
4. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
5. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. Solaris
Here is my problem:
I have an 1.5TB disk with OpenSolaris (b134, b151a) using non AHCI. I then changed to AHCI in BIOS, which results in severe problems: I can not boot the system.
I suspect the problem is because I changed to AHCI. Now I have changed back to non AHCI, but still I can not... (0 Replies)
Discussion started by: kebabbert
0 Replies
8. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
9. Linux
Hi,
a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced.
here is how I did that.
1) created identical partition table on the new disk.
2) attached the mirrors using md commands.
The whole procedure is given below:... (2 Replies)
Discussion started by: busyboy
2 Replies
LEARN ABOUT NETBSD
cmdide
CMDIDE(4) BSD Kernel Interfaces Manual CMDIDE(4)
NAME
cmdide -- CMD Technology and Silicon Image IDE disk controllers driver
SYNOPSIS
cmdide* at pci? dev ? function ? flags 0x0000
options PCIIDE_CMD064x_DISABLE
options PCIIDE_CMD0646U_ENABLEUDMA
DESCRIPTION
The cmdide driver supports the CMD Technology PCI0640, PCI0643, PCI0646, PCI0648, PCI0649, and Silicon Image 0680 IDE controllers, and pro-
vides the interface with the hardware for the ata(4) driver.
The 0x0002 flag forces the cmdide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO
ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
BUGS
There's no way to reliably know if a PCI064x controller is enabled or not. If the driver finds a PCI064x, it will assume it is enabled
unless the PCIIDE_CMD064x_DISABLE option is specified in the kernel config file. This will be a problem only if the controller has been dis-
abled in the BIOS and another controller has been installed and uses the ISA legacy I/O ports and interrupts.
The PCI0646U controller is known to be buggy with Ultra-DMA transfers, so Ultra-DMA is disabled by default for this controller. To enable
Ultra-DMA, use the PCIIDE_CMD0646U_ENABLEUDMA option. Ultra-DMA can eventually be disabled on a per-drive basis with config flags, see
wd(4).
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD
December 13, 2003 BSD