07-21-2011
Indeed, and your point is ?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
4. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
10. Solaris
I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network.
My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network.
I am using the current version of Solaris 10 in... (7 Replies)
Discussion started by: BradJM
7 Replies
LEARN ABOUT OSX
tk_coordstowindow
Tk_CoordsToWindow(3) Tk Library Procedures Tk_CoordsToWindow(3)
__________________________________________________________________________________________________________________________________________________
NAME
Tk_CoordsToWindow - Find window containing a point
SYNOPSIS
#include <tk.h>
Tk_Window
Tk_CoordsToWindow(rootX, rootY, tkwin)
ARGUMENTS
int rootX (in) X-coordinate (in root window coordinates).
int rootY (in) Y-coordinate (in root window coordinates).
Tk_Window tkwin (in) Token for window that identifies application.
_________________________________________________________________
DESCRIPTION
Tk_CoordsToWindow locates the window that contains a given point. The point is specified in root coordinates with rootX and rootY (if a
virtual-root window manager is in use then rootX and rootY are in the coordinate system of the virtual root window). The return value from
the procedure is a token for the window that contains the given point. If the point is not in any window, or if the containing window is
not in the same application as tkwin, then NULL is returned.
The containing window is decided using the same rules that determine which window contains the mouse cursor: if a parent and a child both
contain the point then the child gets preference, and if two siblings both contain the point then the highest one in the stacking order
(i.e. the one that's visible on the screen) gets preference.
KEYWORDS
containing, coordinates, root window
Tk Tk_CoordsToWindow(3)