Hi Folks!
I am a MacUser and am trying to learn Unix for the last few months.
I will explain in detail what I am trying to do, and apreciate you help if you can teach me even if it is a single comand line inside the script.
I own a small company, where I manufacture special gypsums and... (5 Replies)
Hi All,
I want to read username and lastupdate only from /etc/security/passwd and write the same data to another file:
The data in /etc/security/passwd will be in this form for example:
For more details : http://www.unet.univie.ac.at/aix/files/aixfiles/passwd_security.htm#A1219924
smith:... (0 Replies)
Actually i am working with two diffrent files having same structure
each file contain Ten diffrent column and i want to write a script
which will compare the colummns of first file with the column of second file and diiference will be send to the first column of third file .
similarly for... (5 Replies)
UNIX shell script (Bourne shell syntax) called
admin_script. This script is described below as a usage summary:
admin_script
Note: if no options are specified, a menu is displayed which allows
users to perform one of the following tasks and then exit. If
incorrect options are provided,... (1 Reply)
Hello,
I have done some BASIC shell scripting/PERL scripting before so I am familiar with the languages. I am not really sure which one would lend itself better to the application I have to write.
I am required to scan the message logs for possible break in attempts. If I use shell scripting... (2 Replies)
Hi All,
I have written the following script. I have just repeated some commands, and I am sure there is a more better way to do it. I hope I one of gurus here will help me make it in a better shape. Here is the script:
#! /bin/sh
sed -i -e "s/test2.xxx/test3.xxx/" -e "s/output2/output3/"... (2 Replies)
I am adapting an Open Step ping server script to Ubuntu 8.10 and one section of my script isn't working
# if there are servers that just went down or came back up, notify
# with high importance
if ; then
echo notifying of servers that are up again or just now down
notify high
# if there... (2 Replies)
If I need delete some disk,
for i in hdisk1 hdisk2 hdisk3 hdisk4
do
rmdev -dl $i
done
if I have more than 100 hdisks, how to write a script like that to delete them? (6 Replies)
Hi there :rolleyes:
I have a folder called backup
it is path is: ~/backup
Inside this folder, there are four files:
~/backup/test1.cpp
~/backup/test2.cpp
~/backup/test3.cpp
~/backup/PATHS.TXT
The fourth file PATHS.TXT contains the original paths for the three files. This is the... (4 Replies)
Hi,
We have smb client running on two of the linux boxes and smb server on another linux system. During a backup operation which uses smb, read of a file was allowed while write to the same file was going on.Also simultaneous writes to the same file were allowed.Following are the settings in the... (1 Reply)
Discussion started by: swatidas11
1 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)