Here's a conundrum. I use a ThinkPad (T30) which has a slot on the side for the hard drive. It is very easy to swap this with another hard drive which I keep as a backup. Now when I copy the Linux partition from my (in use) hard drive to the backup one (in my UltraBay slot) it takes only 30 minutes. If instead I copy this partition to my storage drive (in my docking station's drive slot) and save it as a file, the same copying takes 2 and a half hours. How come so much longer? Any thoughts?
From the hard drive to the backup I use this:
From the hard drive to a storage drive I use:
Note that the file size is 18.0GB and the partition size is 28.6GB.
Last edited by pludi; 06-13-2011 at 09:32 AM..
Reason: Additional information added.
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
I presently backup my multi-OS multi-paritition boot drive (fedora core 4/ext3, WinXPServer/NTFS, WinXPHome/FAT32) with the command:
telinit 1; cp /dev/sda /dev/sdb
And this works.
Is there a command to only copy a single partition instead of an entire device?
And what about the grub... (12 Replies)
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Scenario:
I would want to copy my / to /mnt, and to avoid recursion exclude /mnt.
cp -avx / /mnt
If i use the above i believe it would run recursively, and end up in mess. So how to do it ?!
Basically this / is sda1, and /mnt is sda2 and sda1 is where only OS is available & currently... (2 Replies)
I have found a question from the exercises of my study mat. The question is
"Why are there a in-core copy and a disk-copy of i-node block and super block?"
If any one know the proper answer then please send me..... (1 Reply)
This is now a larger script than I would customarily post. But many folks have become accustom to getting it off this forum.
Every couple of years I update my favorite scripts. This script is one that I use regularly and have posted older versions every couple of years. I noticed that it has... (3 Replies)
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
LEARN ABOUT REDHAT
hd
HD(4) Linux Programmer's Manual HD(4)NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO mknod(1), chown(1), mount(8), sd(4)Linux 1992-12-17 HD(4)