Here's a conundrum. I use a ThinkPad (T30) which has a slot on the side for the hard drive. It is very easy to swap this with another hard drive which I keep as a backup. Now when I copy the Linux partition from my (in use) hard drive to the backup one (in my UltraBay slot) it takes only 30 minutes. If instead I copy this partition to my storage drive (in my docking station's drive slot) and save it as a file, the same copying takes 2 and a half hours. How come so much longer? Any thoughts?
From the hard drive to the backup I use this:
From the hard drive to a storage drive I use:
Note that the file size is 18.0GB and the partition size is 28.6GB.
Last edited by pludi; 06-13-2011 at 09:32 AM..
Reason: Additional information added.
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
I presently backup my multi-OS multi-paritition boot drive (fedora core 4/ext3, WinXPServer/NTFS, WinXPHome/FAT32) with the command:
telinit 1; cp /dev/sda /dev/sdb
And this works.
Is there a command to only copy a single partition instead of an entire device?
And what about the grub... (12 Replies)
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Scenario:
I would want to copy my / to /mnt, and to avoid recursion exclude /mnt.
cp -avx / /mnt
If i use the above i believe it would run recursively, and end up in mess. So how to do it ?!
Basically this / is sda1, and /mnt is sda2 and sda1 is where only OS is available & currently... (2 Replies)
I have found a question from the exercises of my study mat. The question is
"Why are there a in-core copy and a disk-copy of i-node block and super block?"
If any one know the proper answer then please send me..... (1 Reply)
This is now a larger script than I would customarily post. But many folks have become accustom to getting it off this forum.
Every couple of years I update my favorite scripts. This script is one that I use regularly and have posted older versions every couple of years. I noticed that it has... (3 Replies)
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
LEARN ABOUT PLAN9
wren
WREN(3) Library Functions Manual WREN(3)NAME
wren, ata - hard disk interface
SYNOPSIS
bind #H[drive] /dev
bind #w[target[.lun]] /dev
/dev/hd0disk
/dev/hd0partition
/dev/sd0disk
/dev/sd0partition
...
DESCRIPTION
The hard disk interfaces (wren, #w, is a SCSI disk; ata, #H, is an IDE or ATA disk) serve a one-level directory giving access to the hard
disk partitions. The parameter to attach defines the numerical SCSI target and logical unit number or the IDE drive number to access.
Both default to zero.
Each partition name is prefixed by hd and the numeric drive identifier. The partition always exists and covers the entire disk. The size
of each partition as reported by stat(2) is the number of bytes in the partition, so the size of is the size of the entire disk.
The partition also always exists; it is the last block on the disk for SCSI, second to last for IDE. If it contains valid partition data,
those partitions will be visible as well. Every time the device is bound, the partitions are updated to reflect any changes in the parti-
tion file.
The format of the partition file is the string
plan9 partitions
on a line, followed by partition specifications, one per line, consisting of a name and textual strings for the block start and limit for
each partition on the disk.
The program prep(8) writes the partition table for the disk; its use is preferred to writing it by hand.
SEE ALSO prep(8), scsi(3)SOURCE
/sys/src/9/port/devwren.c
/sys/src/9/pc/devata.c
WREN(3)