05-25-2011
Hi,
I think wireshark is your friend.
The homepage is wireshark.org
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
there are commands to monitor the memory, paging, io... how about network traffic. i mean commands to see whether the network traffic (LAN) is congested? the closest i got is netstat
thanks (6 Replies)
Discussion started by: yls177
6 Replies
2. Cybersecurity
Hi,
Can someone give me the clue on how to capture network traffic at gateway.
Thanx (2 Replies)
Discussion started by: kayode
2 Replies
3. UNIX for Advanced & Expert Users
I want to monitor network traffic. For this purpose i use snoop command. But snoop command only show those packets which are broadcasted or those packets which recieved by host. But I want to examine whole network traffic. Please tell me how to use snoop for monitoring whole network traffic or if... (3 Replies)
Discussion started by: mansoorulhaq
3 Replies
4. Infrastructure Monitoring
Hi all,
Got a strange one here, well not so much strange, different :-)
I need to work out if a server is particulary chatty, whether its talking / communicating heavily to a particular server, as Im planning to physically move the server to a different server, over a link. Hence the... (6 Replies)
Discussion started by: sbk1972
6 Replies
5. HP-UX
I Colleagues,
Somebody can say me how to monitoring traffic in the network. also I am interested in monitoring memory. if somebody to know a guide with command advanced in unix welcome for me.
Thank you for adcanced. (0 Replies)
Discussion started by: systemoper
0 Replies
6. IP Networking
hi all
i want to extract few connection level features (not packet level )of the internet traffic through ethernet card interface
the features are as follows
Timestamp Timestamp of paket captured
Duration duration of connection
ip_proto IP... (0 Replies)
Discussion started by: vaibhavkorde
0 Replies
7. Cybersecurity
hi all
i want to extract few connection level features (not packet level )of the internet traffic through ethernet card interface
the features are as follows
Timestamp Timestamp of paket captured
Duration duration of connection
ip_proto IP... (0 Replies)
Discussion started by: vaibhavkorde
0 Replies
8. Infrastructure Monitoring
If I would like to know what connection , data , traffic in a network port ( eth0 ) , what can I do ?
ps. because I always found the network is very slow , so I would like what the network port is doing .
Thanks
Login ID ust3 is currently in read-only mode for multiple infractions. Creating... (0 Replies)
Discussion started by: ust03
0 Replies
9. UNIX for Advanced & Expert Users
Hi All
I am resilience testing an application that is spread across multiple servers.
One thing I will need to do soon is throttle the network traffic for specific interfaces within the test cluster. Specifically, maybe make a connection take twice or three times as long to respond....
I... (3 Replies)
Discussion started by: bbq
3 Replies
10. IP Networking
My son does homework on a school laptop. I was thinking about setting up a gateway on my home network, so that I can monitor web traffic and know if he is doing his homework without standing over his shoulder. Ideally I would like to use the Raspberry Pi Model b that I already have. However, I... (15 Replies)
Discussion started by: gandolf989
15 Replies
FAITH(4) BSD Kernel Interfaces Manual FAITH(4)
NAME
faith -- IPv6-to-IPv4 TCP relay capturing interface
SYNOPSIS
device faith
DESCRIPTION
The faith interface captures IPv6 TCP traffic, for implementing userland IPv6-to-IPv4 TCP relay like faithd(8).
Each faith interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using
the cloned_interfaces variable in rc.conf(5).
Special action will be taken when IPv6 TCP traffic is seen on a router, and the routing table suggests to route it to the faith interface.
In this case, the packet will be accepted by the router, regardless of the list of IPv6 interface addresses assigned to the router. The
packet will be captured by an IPv6 TCP socket, if it has the IN6P_FAITH flag turned on and matching address/port pairs. As a result, faith
will let you capture IPv6 TCP traffic to some specific destination addresses. Userland programs, such as faithd(8) can use this behavior to
relay IPv6 TCP traffic to IPv4 TCP traffic. The program can accept some specific IPv6 TCP traffic, perform getsockname(2) to get the IPv6
destination address specified by the client, and perform application-specific address mapping to relay IPv6 TCP to IPv4 TCP.
The IN6P_FAITH flag on a IPv6 TCP socket can be set by using setsockopt(2), with level IPPROTO_IPV6 and optname IPv6_FAITH.
To handle error reports by ICMPv6, some ICMPv6 packets routed to an faith interface will be delivered to IPv6 TCP, as well.
To understand how faith can be used, take a look at the source code of faithd(8).
As the faith interface implements potentially dangerous operations, great care must be taken when configuring it. To avoid possible misuse,
the sysctl(8) variable net.inet6.ip6.keepfaith must be set to 1 prior to using the interface. When net.inet6.ip6.keepfaith is 0, no packets
will be captured by the faith interface.
The faith interface is intended to be used on routers, not on hosts.
SEE ALSO
inet(4), inet6(4), faithd(8)
Jun-ichiro itojun Hagino and Kazu Yamamoto, An IPv6-to-IPv4 transport relay translator, RFC3142.
HISTORY
The FAITH IPv6-to-IPv4 TCP relay translator first appeared in the WIDE hydrangea IPv6 stack.
BSD
April 10, 1999 BSD