03-18-2011
Here is little info, hope it helps:
(1) how do I know what is the LUN ID.
-> Depands on the driver which you are using.
for example: if using linux native multipathing then "multipath -ll" will show you the Lun & their details.
If using, third party drivers related to SAN:
for example - Rdac/mpp from IBM then u can use mppUtil -a <storage name>, will show u all the details of Luns...
(3) how do I scan for new LUNs.
again if using linux native multipath then run "rescan-scsi-bus.sh" avaialbe from sg3_utils rpm.
If using third party, for example Rdac of IBM: run "mppBusScan" and it will detect the new LUNs.
Hope it helps....
~Titans~
This User Gave Thanks to titanic4u For This Post:
10 More Discussions You Might Find Interesting
1. Slackware
hi,
i m tryin to learn ldap.
but its not getting configured.
the error msg it shows is:
LDAP configure error: BDB/HDB : Berkeley DB version incompatibe.
The BDB version i have installed is bdb4.2.52 and the ldap version is openldap-2.3.12.
my machine is running on red hat linux 9.
Why... (1 Reply)
Discussion started by: mridula
1 Replies
2. UNIX for Advanced & Expert Users
Hi Gurus:)
I have to connect from a SunOS 5.10 to a 5.8 using sftp in BatchMode. For this, I have generated a Public-Key (ssh-keygen -b 1024 -P "" -t dsa) on the 5.10 and saved it in ~remote-user/.ssh/authorized-keys on the 5.8.
Then, running either one of ssh or sftp, it asks for the... (24 Replies)
Discussion started by: unilover
24 Replies
3. UNIX for Dummies Questions & Answers
Is there a way to find the raid type without restarting the machine?
I m using linux operating system. (3 Replies)
Discussion started by: pinga123
3 Replies
4. UNIX for Dummies Questions & Answers
What are the two ways the hardware clock can be configured under Linux?
Thanks (3 Replies)
Discussion started by: lemon_06
3 Replies
5. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
6. HP-UX
Following this thread :
https://www.unix.com/hp-ux/189023-solved-way-tell-printer-used-configured-print-queue.html
This is rwuerth's nice contribution!
I had a more complicated script written a long time ago to find out this information,
but after realizing due to VBE's post (thank you VBE)... (0 Replies)
Discussion started by: rwuerth
0 Replies
7. UNIX for Dummies Questions & Answers
Hi all,
I have an environment with Aix and Linux severs zoned to tape drives
I'd like to list HBAs WWN on my servers which are zoned to the drives.
Thanks (1 Reply)
Discussion started by: Sara_84
1 Replies
8. IP Networking
Hi have a solaris server with the following IP 192.168.0.85, but anybody can login in using 172.19.0.85, and the ifconfigcommand does not show the 172.19.05 .
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask... (6 Replies)
Discussion started by: fretagi
6 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
10. Debian
I have kali running on vbox as :-
/etc/network/interfaces
ifup eth0 gives me
tpcdump (0 Replies)
Discussion started by: lazerz
0 Replies
LEARN ABOUT CENTOS
ipsec_tncfg
IPSEC_TNCFG(5) [FIXME: manual] IPSEC_TNCFG(5)
NAME
ipsec_tncfg - lists IPSEC virtual interfaces attached to real interfaces
SYNOPSIS
ipsec tncfg
cat/proc/net/ipsec_tncfg
OBSOLETE
Note that tncfg is only supported on the classic KLIPS stack. It is not supported on any other stack and will be completely removed in
future versions. A replacement command still needs to be designed
DESCRIPTION
/proc/net/ipsec_tncfg is a read-only file which lists which IPSEC virtual interfaces are attached to which real interfaces, through which
packets will be forwarded once processed by IPSEC.
Each line lists one ipsec I/F. A table entry consists of:
+
an ipsec virtual I/F name
+
a visual and machine parsable separator '->', separating the virtual I/F and the physical I/F,
+
a physical I/F name, to which the ipsec virtual I/F is attached or NULL if it is not attached,
+
the keyword mtu=,
+
the MTU of the ipsec virtual I/F,
+
the automatically adjusted effective MTU for PMTU discovery, in brackets,
+
a visual and machine parsable separator '->', separating the virtual I/F MTU and the physical I/F MTU,
+
the MTU of the attached physical I/F.
EXAMPLES
ipsec2 -> eth3 mtu=16260(1443) -> 1500
shows that virtual device ipsec2 with an MTU of 16260 is connected to physical device eth3 with an MTU of 1500 and that the effective MTU
as a result of PMTU discovery has been automatically set to 1443.
ipsec0 -> wvlan0 mtu=1400(16260) -> 1500
shows that virtual device ipsec0 with an MTU of 1400 is connected to physical device wvlan0 with an MTU of 1500 and no PMTU packets have
gotten far enough to bump down the effective MTU from its default of 16260.
ipsec3 -> NULL mtu=0(0) -> 0
shows that virtual device ipsec3 is not connected to any physical device.
FILES
/proc/net/ipsec_tncfg, /usr/local/bin/ipsec
SEE ALSO
ipsec(8), ipsec_manual(8), ipsec_eroute(5), ipsec_spi(5), ipsec_spigrp(5), ipsec_klipsdebug(5), ipsec_tncfg(8), ipsec_version(5),
ipsec_pf_key(5)
HISTORY
Written for the Linux FreeS/WAN project <http://www.freeswan.org/> by Richard Guy Briggs.
[FIXME: source] 10/06/2010 IPSEC_TNCFG(5)