11-22-2010
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. Filesystems, Disks and Memory
Hello all,
I'm trying to install SCO openserver 5 on a 2.5 Gig hard drive, and I tried fdisk and a low-level format of the drive. When I insert the boot diskette all seems fine, and it asks me to set the cd-rom and it sees it and reads from it. Well, I'm thinking all is well until right after I... (1 Reply)
Discussion started by: immulett
1 Replies
4. UNIX for Dummies Questions & Answers
I have just been made responsible for setting up Apache on our office SCO
box. I have searched the internet, but
haven't found any details that I can make
sense of. I'm unfamiliar with Unix and would appreciate any help members of
the forum have to offer. (1 Reply)
Discussion started by: cstovall
1 Replies
5. SCO
Dear members
when i installed dual processor patch in openserver 5.0.7 in hp ML370 G4 server it hangs in sco at G_hd_config.
i tried MP4, EFS 5.64,5.70A but not solved the problem.. (0 Replies)
Discussion started by: M_farooqui
0 Replies
6. SCO
I need SCO Openserver 4.2. Please, give me distributive of that version SCO:eek: (0 Replies)
Discussion started by: caine
0 Replies
7. SCO
Even though IBM states that the x3500 server is Openserver 6.x compatible, it is still a bit of a trick to install SCO Openserver 6 to the machine because the standard method of installing the BTLD required to install the OS requires that the driver be written to a floppy which doesn't exist on... (3 Replies)
Discussion started by: qkrenge
3 Replies
8. SCO
hi
Howto install SCO Openserver 5.0.7 as a trial or howto get a trial license number? (0 Replies)
Discussion started by: ccc
0 Replies
9. SCO
Hi
I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question:
PCI BUS#
DEVICE#... (3 Replies)
Discussion started by: TinhNhi
3 Replies
10. SCO
hi
Howto install iperf on SCO OpenServer 5.0.7? (0 Replies)
Discussion started by: ccc
0 Replies
URL(4) BSD Kernel Interfaces Manual URL(4)
NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8)
HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
September 18, 2006 BSD