11-17-2010
This User Gave Thanks to kopper For This Post:
9 More Discussions You Might Find Interesting
1. Solaris
Thinking of using our San for network backups..
Have a Netra 240 being installed and planning to get some space on our San.
Do you know what software is used to access the San from my server or what I would need to do? I know how to connect to local storage, disk arrays etc but not sure what... (1 Reply)
Discussion started by: frustrated1
1 Replies
2. Filesystems, Disks and Memory
Hi,
I have an existing SUN server that has a SAN storage installed on it. It also has softwares like Appwrox(scheduler), Taradata (database client), Samba Share and a few more installed on it.
Now suppose that I have a new unix server server and i switch the same SAN store from the old unix... (1 Reply)
Discussion started by: myloginid
1 Replies
3. AIX
I have 3 SAN disks of 1 TB each. Is it more efficient to make 1 large Volume group with multiple LV's or 3 Volume Groups with 1 LV each. The SAN disk is where all my backups will be dumped.:confused: (1 Reply)
Discussion started by: daveisme
1 Replies
4. Solaris
Hi,
I have configured our SAN Storage to be connected to our new SUN T5220.
On the SAn it looks all fine
on the server I do not see any connection:
cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c1 scsi-bus connected ... (4 Replies)
Discussion started by: manni2
4 Replies
5. Red Hat
Hello,
I am using LINUX OS. I want to check what is the SAN storage size. How do i check this in server? Any help is really appreciated.. (3 Replies)
Discussion started by: govindts
3 Replies
6. Solaris
HI all,
I had recently change the Server storage from EMC to the IBM SAN.
but after the configuration, the IBM success to see the server HBA port and successfully assign a LUN for the server.
When i go to the server, and restarted it. i use the "format" command to check, but din see any... (1 Reply)
Discussion started by: SmartAntz
1 Replies
7. Solaris
Hi,
We are planning to setup a 10gR2 RAC and storage on ASM. We use Sun StorEdge SAN.
The installation and configuration manual says to configure ASM diskgroups with raw devices (preferably raw disk not volumes).
I dont really know if its possible to present raw disks to the Solaris... (4 Replies)
Discussion started by: esmgr
4 Replies
8. AIX
Can anyone recommend a good book on san storage basics and how it communicates with an AIX server? (1 Reply)
Discussion started by: NycUnxer
1 Replies
9. Solaris
hi all,
I am on solaris 10 1/13 and new to SAN storage.
I am required to connect to the LUNs on the SAN storage and is asked to provide the WWN information to the storage administrator.
Right now, it will be just 1 connection from a single hba port to the FCport on the storage directly,... (1 Reply)
Discussion started by: javanoob
1 Replies
URL(4) BSD Kernel Interfaces Manual URL(4)
NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8)
HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
September 18, 2006 BSD