11-05-2010
how do you connect the box to your blade? please discribe in detail... which scsi card do you use and so on...
10 More Discussions You Might Find Interesting
1. Solaris
Hi folks,
I´m having a problem with a Ultra60 box with diff scsi pci card
conected to one D1000. The conection are correct because a checked the
D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all
disks one time then the led of one of the disks powers off and then
nothing... (2 Replies)
Discussion started by: spacewalker
2 Replies
2. Solaris
Sorry if this seems trivial. i have been given a task at work to configure a sun processing server "enterprise 4500" so it can work with the a storage server "storedge A5200" and "storedge D1000"
the truth is i have never worked on a sun server before. i need a guideline (step by step) as to... (5 Replies)
Discussion started by: lawalidowu
5 Replies
3. Solaris
Do you know how do I make my solaris 8 detect the storEDGE A5000?.
I have problem making it recognise, without that I cannot install VxVM.
Any ideas? (7 Replies)
Discussion started by: calsum
7 Replies
4. UNIX for Advanced & Expert Users
Hi All,
Is there anyway two nodes can share D1000 or minipack with 6 disk slots.
Right now I have minipacks and I am connecting to Sunblade 100 and Sunbladew 150 separately. I would like to connect two systems to one minipack and able see the all the disks on both systems.
I do have D1000... (0 Replies)
Discussion started by: sriny
0 Replies
5. Solaris
Hello,
I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks.
It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused!
So,... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
6. Solaris
Hi Community,
I'm working on Solaris 10 installation with 1 Sun Server V490 and 1 StoredgeTek 3510 (Standalone configuration).
I connected the Server to the Storedge with 1 fiber cables and I created 3 LUNs with RAID1 Configuration.
Today I've a problem, infact I have to connect a second... (3 Replies)
Discussion started by: Sunb3
3 Replies
7. Solaris
Hi Community,
could you provide me a procedure or solaris 10 tool/command or Veritas command to check ths Storedge IP?
Thank you!!! (4 Replies)
Discussion started by: Sunb3
4 Replies
8. Solaris
Hi,
Recently i was trying to connect Sun Storedge D1000 Array to E420 R (Practice servers). I connected the SCSI cable between array and server. I tried the following :
#devfsadm (nothing showed up)
#format (no new disk is shown here)
i tried this process again after putting ON the... (2 Replies)
Discussion started by: bluegold86
2 Replies
9. Solaris
Hi,
My question is What is StorEdge in Solairs?
What are A1000 AND D1000? (3 Replies)
Discussion started by: aparna66
3 Replies
10. Solaris
Hi everyone,
I am hoping anyone of you could help me in this weird problem we have in 1 of our Solaris 10 servers. Lately, we have been having some ftp problems in this server. Though it can ping any server within the network, it seems that it can only ftp to a select few. For most servers, the... (4 Replies)
Discussion started by: labdakos
4 Replies
LEARN ABOUT REDHAT
sane-coolscan
sane-coolscan(5) File Formats Manual sane-coolscan(5)
NAME
sane-coolscan - SANE backend for Nikon film-scanners
ABOUT THIS FILE
This file is a short descripton of the coolscan-backend for sane!
DESCRIPTION
The sane-coolscan library implements a SANE backend that provides the interface to the following Nikon Coolscan Film scanners: Nikon LS20,
LS30, LS1000, LS2000.
Even though the backend has worked for a number of people, there are still some problems, especially in combination with some SCSI
card/drivers (AHA-1505/aha152x.o) and the autofocus command. You should consider this backend 'alpha' and be carefull when using it the
first time.
CONFIGURATION
The configuration file for this backend resides in /etc/sane.d/coolscan.conf.
Its contents is a list of device names that correspond to Nikon Coolscan scanners. Empty lines and lines starting with a hash mark (#) are
ignored. A sample configuration file is shown below:
#scsi Vendor Model Type
scsi Nikon * Scanner
/dev/scanner
The special device name must be a generic SCSI device or a symlink to such a device. To find out to which device your scanner is assigned
and how you have to set the permissions of that device, have a look at sane-scsi.
SCSI ADAPTER TIPS
Some SCSI-adapters and low-level SCSI drivers do not work correctly with this backend and the Coolscan scanners. These systems hang when
the autofocus command is send to the Scanner. To see a list of which card/driver combinations work or dont work have a look at:
http://andreas.rick.free.fr/sane/autofocus.html.
FILES
The backend configuration file:
/etc/sane.d/coolscan.conf.
The static library implementing this backend:
/usr/lib/sane/libsane-coolscan.a
The shared library implementing this backend:
/usr/lib/sane/libsane-coolscan.so
(present on systems that support dynamic loading)
ENVIRONMENT
SANE_DEBUG_COOLSCAN
If the library was compiled with debug support enabled, this environment variable controls the debug level for this backend. E.g., a value
of 128 requests all debug output to be printed. Smaller levels reduce verbosity: SANE_DEBUG_COOLSCAN values
Examples:
on bash:
export SANE_DEBUG_COOLSCAN=8
on csh
setenv SANE_DEBUG_COOLSCAN 8
BUGS
The autofocus command does not work with some SCSI card/driver combinations
The gamma table is not implemented for the LS1000 yet.
The dust-removal is not working yet
SEE ALSO
http://andreas.rick.free.fr/sane/ The homepage of this backend
http://www.sema.be/coolscan/ The original version of the coolscan backend by Didier
sane(7), sane-scsi(5)
THANKS TO
Didier Carlier - For writing the original Coolscan backend (without it I would not have started this)
Oliver.Rauch - For adapting xsane so quickly to the infrared stuff.
All the other people working on SANE.
AUTHOR
Andreas Rick
EMAIL-CONTACT
andreas.rick@free.fr
4 July 2000 sane-coolscan(5)