If you receive an error (like device busy) you can use lsof or fuser to see what processes are accessing the mount point.
If you don't want it to be mounted again at the next reboot, remove it from, or comment it out in, /etc/fstab or change it's options to prevent it. (that's OS-specific - what is your OS?)
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
hi all,
I am new to AIX as well as UNIX also ,i have a question
One of my program has created a new filesystem on the system.....
df shows :
/dev/fslv04 2031616 2030648 1% 3 1% /replicas/source
when i tried to umount the above filesystem by
umount... (3 Replies)
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Hi,
I know that if we need to unmount a device, we use the command umount mount-point, example 'umount /tmp/mount1'
But We can also unmount the device with device name example 'umount /dev/hda6'.
NOTE: I think in RHEL3 we cannot unmount with device name. Correct me if I am wrong.
What... (1 Reply)
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
I have installed Solaris 11 Express on my machine, created a raidz2 zpool named shares and set up sharing (zfs set sharesmb=on shares). I also created a script for automatic backuping using snapshots.
Everything worked fine. But yesterday I tried recovering from one of those backuped snapshots:... (1 Reply)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
As stated, I am looking into keeping my backup drive unmounted in normal windows use. Partly this is to address threats like cryptolocker. Since one of my backup drives is an internal drive, it will not likely afford any protection from such a threat. I am thinking of adding code to my rsync script... (5 Replies)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
LEARN ABOUT PLAN9
wren
WREN(3) Library Functions Manual WREN(3)NAME
wren, ata - hard disk interface
SYNOPSIS
bind #H[drive] /dev
bind #w[target[.lun]] /dev
/dev/hd0disk
/dev/hd0partition
/dev/sd0disk
/dev/sd0partition
...
DESCRIPTION
The hard disk interfaces (wren, #w, is a SCSI disk; ata, #H, is an IDE or ATA disk) serve a one-level directory giving access to the hard
disk partitions. The parameter to attach defines the numerical SCSI target and logical unit number or the IDE drive number to access.
Both default to zero.
Each partition name is prefixed by hd and the numeric drive identifier. The partition always exists and covers the entire disk. The size
of each partition as reported by stat(2) is the number of bytes in the partition, so the size of is the size of the entire disk.
The partition also always exists; it is the last block on the disk for SCSI, second to last for IDE. If it contains valid partition data,
those partitions will be visible as well. Every time the device is bound, the partitions are updated to reflect any changes in the parti-
tion file.
The format of the partition file is the string
plan9 partitions
on a line, followed by partition specifications, one per line, consisting of a name and textual strings for the block start and limit for
each partition on the disk.
The program prep(8) writes the partition table for the disk; its use is preferred to writing it by hand.
SEE ALSO prep(8), scsi(3)SOURCE
/sys/src/9/port/devwren.c
/sys/src/9/pc/devata.c
WREN(3)