07-30-2010
Mircolite Edge
Microlite Corporation - Home of BackupEDGE 3.0 is probably the easiest, if just want to replace the hard drive. Depending upon how different the new hardware configuration is, you may have to load new device drivers etc.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Currently, I am planning a migration between machine which under True64UNIX. The new machine will run with higher version O/S. My question is, is there any solution on migrating one machine to another which with different O/S version? My goal is keeping minimum impact to the users.
Excuse my... (1 Reply)
Discussion started by: coolmans
1 Replies
2. Solaris
If I have an oracle 9 database environment on a san running solaris 5.8 as the os. Can I plug the san into a Solaris 5.9 environment and have the database work ? - as long as binaries are on the san (1 Reply)
Discussion started by: tim-carroll@com
1 Replies
3. Linux
Hi ,
I would like to (MYSQL) migrate the all the data from solari's to linux box.
I have checked whether mysql is installed or not.
rpm -qa | grep -i mysql
I confirmed !!!!
I want to know the following points.
1) How can get to know what are mysql data files and location as well.... (4 Replies)
Discussion started by: Mani_apr08
4 Replies
4. Solaris
Hi folk,
I have this hardware faunty message, but dont know which hardware is this ? can you guide me ?
--------------- ------------------------------------ -------------- ---------
TIME EVENT-ID MSG-ID SEVERITY
---------------... (9 Replies)
Discussion started by: dehetoxic
9 Replies
5. SCO
Good afternoon all,
I'm a bit stuck... I honestly don't know very much about Unix let alone UnixWare for that matter. I have a system that's very old and could fail really at any time. I have another server I'd like to move everything to yet I don't know what's possible. The current server is... (2 Replies)
Discussion started by: rubiks015
2 Replies
6. SCO
I run SCO 5.0.7v in ESXi 5.5 and am looking at ways to increase performance. I notice that the VM hardware is still set to 4 and wondered if there was an advantage in raising it or will this cause issues? (0 Replies)
Discussion started by: stewartg
0 Replies
7. SCO
Looking for a modern server to run SCO OSR 5.0.7 without VM (native), h/w must have manufacturers warranty.
Requirements would be to accommodate light loads of up to 15 users, app does not take more than 30 - 40 MB of RAM and data stored takes up to 15 - 20 GB, no internet connections... (3 Replies)
Discussion started by: migurus
3 Replies
8. Linux
Hi all,
Please explain how do i. Migrate and backup a running lvm..!!
Thanks,
Sent from my LG-D802 using Tapatalk (3 Replies)
Discussion started by: lordkizzo
3 Replies
9. AIX
Hello Friends/AIXgurus,
When you have time, could you please look into below. We're planning to migrate AIX LPARs on to new Hardware.
Requirement: Migrate AIX LPARs from POWER 6 to POWER 8 Hardware (*everything should run as is after the transition)
Below is our thought process. Ours... (5 Replies)
Discussion started by: System Admin 77
5 Replies
URL(4) BSD Kernel Interfaces Manual URL(4)
NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8)
HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
September 18, 2006 BSD