|
|
Sponsored Content
Operating Systems
Solaris
Solaris x86: Bad PBR sig
Post 302439155 by lowbyte on Thursday 22nd of July 2010 03:00:24 AM
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I recentlly installed solaris 8 on a 2G HD successfully ,
but cannot boot pass a screen that has a error message
"BAD PBR".
My queston would be is how do I get pass this and
how do I repair it?
I have visited the SUN SYSTEM website many times
trying to get information.
thanks
Mogfog (2 Replies)
Discussion started by: mogfog
2 Replies
2. UNIX for Dummies Questions & Answers
Well i install successfully Solaris on my Second Hard disk, although i had to make it primary Master and my orignal hard disk as pirmary slave, because solaris will not let Windows on primary master.
Anyway after installation when i try to boot from hard disk , it shows message
bad PBR Sig ... (3 Replies)
Discussion started by: abidmalik
3 Replies
3. Solaris
hello mentor.
I'm getting an error " fdgetchng: write protect check failed "
after I rebooted my laptop because it hangs when i open server management console.
what seems to be the problem?
thanks (3 Replies)
Discussion started by: eykyn17
3 Replies
4. UNIX for Dummies Questions & Answers
ok, i recently posted asking for a distro of unix, and someone said to try solaris, so i booted up the dvd iso installer. And after making some kind of mistake in the preperation, I couldnt retry the installer, it repeated the Warning: Bad Geometry. thing, and when i tried to just boot up into... (0 Replies)
Discussion started by: FaoX666
0 Replies
5. UNIX for Dummies Questions & Answers
I know that Sun make s a version of Solaris for Sparc platforms and also an x86 (Intel/AMD) release of Solaris. Can an application that runs on Solaris/Sparc also run on a PC running the x86 release of Solaris? Would a different release be required or any re-compling of the application?
jim (1 Reply)
Discussion started by: stocksj
1 Replies
6. Solaris
Hai
while booting sun solaris 10 in a intel machine,its showing PBR bad and its showing disk boot failure.but the is detecting.please guide me (1 Reply)
Discussion started by: subbiahvin
1 Replies
7. Solaris
After installing Solaris 10 x86 (solaris 5 2009 update 7 ) i've been granted a “Bad PBR sig” error message on boot, making my system unbootable. any one has any solution for this problem (1 Reply)
Discussion started by: maxim42
1 Replies
8. Solaris
Hi folks.
By disk cloning on Solaris x86, I used a command dd.
I pulled out the source and inserted the new disk.
By loading I have received the following issue: BAD PBR SIGN. :( (5 Replies)
Discussion started by: wolfgang
5 Replies
9. Solaris
Hi,
I am facing an issue with Solaris x86 machine
Machine Details:
uname -a
SunOS sol10-64 5.10 Generic_137138-09 i86pc i386 i86pc
..............................
Description:
I am trying to register a programm with proramm ID 300760 with version number 1, and tryint to create a... (0 Replies)
Discussion started by: DivakarAdari
0 Replies
10. Red Hat
Hi,
I accidentally did this:
wadhwaso@nxsdgd01 deps]$sudo rpm -e --nodeps glibc-2.5-107.x86_64
error: %postun(glibc-2.5-107.x86_64) scriptlet failed, exit status 255
and since then I am not able to run any command on this server except 'cd'.
I always get the following error:
$ ls... (6 Replies)
Discussion started by: stunn3r
6 Replies
LEARN ABOUT NETBSD
url
URL(4) BSD Kernel Interfaces Manual URL(4) NAME
url -- Realtek RTL8150L USB Ethernet driver SYNOPSIS
url* at uhub? urlphy* at mii? DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip. The url driver supports the following adapters: CompUSA USBKR100 GreenHouse GH-USB100B Melco Inc. LUA-KTX Sitecom LN013 For more information on configuring this device, see ifconfig(8). DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8) HISTORY
The url device driver first appeared in NetBSD 1.6. AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>. BSD
September 18, 2006 BSD