10-09-2009
I would take fpmurphy's suggestion and swap them out with a known good the next time they go down. I would also check your logs and see if you see anything in there.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Gentoo
Hi all,
I'm trying to write a script that will turn off the network interface eth0 on a linux Gentoo machine and then turn it back on, any help?
Thanks,
Neked (1 Reply)
Discussion started by: neked
1 Replies
3. Solaris
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Discussion started by: kumarmani
6 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. Solaris
Hi all, I'm new here and looking for some help.
I'm looking for the way to rename the network interfaces for Solaris 10. Got a server with 2 network cards (say "igb0" and "igb1") and there were some reasons that I have to swap the pci slots for those cards. However, after I did that, Solaris 10... (3 Replies)
Discussion started by: bbq9
3 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
veth(4) Linux Programmer's Manual veth(4)
NAME
veth - Virtual Ethernet Device
DESCRIPTION
The veth devices are virtual Ethernet devices. They can act as tunnels between network namespaces to create a bridge to a physical network
device in another namespace, but can also be used as standalone network devices.
veth devices are always created in interconnected pairs. A pair can be created using the command:
# ip link add <p1-name> type veth peer name <p2-name>
In the above, p1-name and p2-name are the names assigned to the two connected end points.
Packets transmitted on one device in the pair are immediately received on the other device. When either devices is down the link state of
the pair is down.
veth device pairs are useful for combining the network facilities of the kernel together in interesting ways. A particularly interesting
use case is to place one end of a veth pair in one network namespace and the other end in another network namespace, thus allowing communi-
cation between network namespaces. To do this, one first creates the veth device as above and then moves one side of the pair to the other
namespace:
# ip link set <p2-name> netns <p2-namespace>
ethtool(8) can be used to find the peer of a veth network interface, using commands something like:
# ip link add ve_A type veth peer name ve_B # Create veth pair
# ethtool -S ve_A # Discover interface index of peer
NIC statistics:
peer_ifindex: 16
# ip link | grep '^16:' # Look up interface
16: ve_B@ve_A: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc ...
SEE ALSO
clone(2), network_namespaces(7), ip(8), ip-link(8), ip-netns(8)
Linux 2018-02-02 veth(4)