restart the network on freeBSD 7.2 Post: 302357384

9 More Discussions You Might Find Interesting

1. Programming

Application crashes in FreeBSD 7.1 while working ok in FreeBSD 6.3

Hello there, My mulithreaded application (which is too large to represent the source code here) is crashing after installing FreeBSD 7.1-RELEASE/amd64. It worked properly on others machines (Dual Cores with 4GB of RAM - FreeBSD 6.2-RELEASE/i386). The current machine has 2x Core 2 Duo...

2. Programming

Help in developing a Network Appliation to monitor pc in a network

I am developing a Network Appliation to monitor computers in a network. Specs are App monitors the current web page viewed in each system App also can shutdown the computer in the network App can show all process run by each computer in the network I am now confused how to start my...

3. IP Networking

ssh server is attachable from local network not from another network

hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no...

4. AIX

How restart the network interface in AIX?

Hi All, Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat. Thanks, Sunil.K please watch out to post in the right subforum!

5. IP Networking

Test Network Routing Issues (FREEBSD and RHEL)

Hello, I'm attempting to setup a test network with a client-server based architecture using a proprietary application. The client works by communicating with the server on separate links (typically cellular connections) and then initiates a tunnel over each active link. However, in place of the...

6. Red Hat

Network becomes slow and return fast only after restart network

Hi, I have 2 machines in production environment: 1. redhat machine for application 2. DB machine (oracle) The application doing a lot of small read&writes from and to the DB machine. The problem is that after some few hours the network from the application to the DB becomes very slow and...

7. IP Networking

I would like to monitor network traffic for a computer on my network

My son does homework on a school laptop. I was thinking about setting up a gateway on my home network, so that I can monitor web traffic and know if he is doing his homework without standing over his shoulder. Ideally I would like to use the Raspberry Pi Model b that I already have. However, I...

8. Solaris

Changing "rx_queue_number" in "ixgbe.conf". Reboot or Network Restart?

Hi all, First post here. Working on Solaris 10, on a Sun t4-4, need to change RX queue depth(ethernet, not HBA) and was wondering if i could get by with just restarting the network or if i should just bounce the whole shebang. Apologies if i missed a similar thread. if there is one, please...

9. Debian

How do i correct restart network-services in Debian?

Hello, I would like to do follow steps. Set a static IP-Adress on eth0 (For Testing) Set DHCP on eth0 All steps should be done without a single reboot. /etc/network/interfaces iface eth0 inet static address 192.0.2.7/24 gateway 192.0.2.254How do i perform...

LEARN ABOUT NETBSD

urtw

URTW(4) 						   BSD Kernel Interfaces Manual 						   URTW(4)

NAME

     urtw -- Realtek RTL8187B/L USB IEEE 802.11b/g wireless network device

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   urtw* at uhub? port ?

DESCRIPTION

     The urtw driver supports USB 802.11b/g wireless adapters based on the Realtek RTL8187B/L.

     urtw supports station and monitor mode operation.	Only one virtual interface may be configured at any time.  For more information on config-
     uring this device, see ifconfig(8).

HARDWARE

     The urtw driver supports Realtek RTL8187B/L based wireless network devices, including:

	   Card Radio Bus
	   Belkin F5D7050E RTL8225 USB
	   Linksys WUSB54GCv2 RTL8225 USB
	   Netgear WG111v2 RTL8225 USB
	   Netgear WG111v3 RTL8225 USB
	   Safehome WLG-1500SMA5 RTL8225 USB
	   Shuttle XPC Accessory PN20 RTL8225 USB
	   Sitecom WL168v1 RTL8225 USB
	   Sitecom WL168v4 RTL8225 USB
	   SureCom EP-9001-g(2A) RTL8225 USB
	   TRENDnet TEW-424UB V3.xR RTL8225 USB

EXAMPLES

     ifconfig.if(5) example configures urtw0 to join whatever network is available on boot, using WEP key ``0x1deadbeef1'', channel 11, obtaining
     an IP address using DHCP:

	   nwkey 0x1deadbeef1 chan 11
	   dhcp

     Configure urtw0 to join network ``my_net'' using WPA with passphrase ``my_passphrase'':

	   # ifconfig urtw0 nwid my_net wpakey my_passphrase

     Join an existing BSS network, ``my_net'':

	   # ifconfig urtw0 192.168.1.1 netmask 0xffffff00 nwid my_net

SEE ALSO

     arp(4), netintro(4), usb(4), ifconfig.if(5), wpa_supplicant.conf(5), ifconfig(8), wpa_supplicant(8)

     Realtek, http://www.realtek.com.tw.

HISTORY

     The urtw device driver first appeared in FreeBSD 8.0.

AUTHORS

     The urtw driver was written by Weongyo Jeong <weongyo@FreeBSD.org>.

BSD
								 October 17, 2009							       BSD