|
|
Sponsored Content
Operating Systems
Solaris
Managing disk array on A1000
Post 302350174 by beginningDBA on Thursday 3rd of September 2009 03:58:54 AM
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Sorry if this is not the right folder...
I come across these terms..
-Disk Array
-Clustering
What are they? When and how will we use them?
Please teach me.
Thanks (1 Reply)
Discussion started by: champion
1 Replies
2. Solaris
Hello friends, i have a problem with the pinout of T3 Array Disk cuz i don't know to build this serial cable :( please anybody help me! (1 Reply)
Discussion started by: nikoxve
1 Replies
3. Solaris
Do you know how do I make my solaris 8 detect the storEDGE A5000?.
I have problem making it recognise, without that I cannot install VxVM.
Any ideas? (7 Replies)
Discussion started by: calsum
7 Replies
4. Solaris
I am new to the unix world. I have SunBlade 100 and A1000 Disk storage array with 12 Hard drives. I used SCSI card and SCSI cables to connect. When I do the format command,I can see disk storage as one disk instead of 12 disks as below. Could anybody can explain why?
What should I do in order... (1 Reply)
Discussion started by: Dulasi
1 Replies
5. UNIX for Advanced & Expert Users
I have a 3510 disk array attached to a T2000 server.
The dmesg command shows disk error as follows and is generated a couple of times during the day
Aug 18 03:35:51 myserver SUNWscsdMonitor: <rctrl6042> Standard General Event, CHL:2 ID:22 Drive NOTICE: Drive Recovered Error - 5F8E1F... (1 Reply)
Discussion started by: Tirmazi
1 Replies
6. Solaris
So I have 2 solaris sun servers one with a disk array with 14 drives which I need to move to the other server. How do I move the disk array configured as a Raid 5 to another server without losing data? So far I know I'll connect the drive, run devfsadm, use format to verify the server see's... (5 Replies)
Discussion started by: Kjons76
5 Replies
7. UNIX for Advanced & Expert Users
HI:
I have a DUAL redundant system running in HP-UX 10.20 ( 2 servers)
Both servers share an external SCSI disk array. Both server runs a Data base wich uses the disk array to write the data, and that is the way they share the information.
The way that the servers see the disk array, is like... (1 Reply)
Discussion started by: pmoren
1 Replies
8. UNIX for Dummies Questions & Answers
Hi there,
I've setup a raid0 array of 3 identical disks using :
mdadm --create --verbose /dev/md0 --level=stripe --raid-devices=3 /dev/sdb1 /dev/sdc1 /dev/sdd1I'm using dstat to monitor the disk activity :
dstat --epoch -D sdb,sdc,sdd --disk-util 30The results show that the stress is not... (8 Replies)
Discussion started by: chebarbudo
8 Replies
9. Filesystems, Disks and Memory
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (1 Reply)
Discussion started by: terrya
1 Replies
10. AIX
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (3 Replies)
Discussion started by: terrya
3 Replies
LEARN ABOUT NETBSD
mfi
MFI(4) BSD Kernel Interfaces Manual MFI(4) NAME
mfi -- LSI Logic & Dell MegaRAID SAS RAID controller SYNOPSIS
mfi* at pci? dev ? function ? DESCRIPTION
The mfi driver provides support for the MegaRAID SAS family of RAID controllers, including: - Dell PERC 5/e, PERC 5/i, PERC 6/e, PERC 6/i - Intel RAID Controller SRCSAS18E, SRCSAS144E - LSI Logic MegaRAID SAS 8208ELP, MegaRAID SAS 8208XLP, MegaRAID SAS 8300XLP, MegaRAID SAS 8308ELP, MegaRAID SAS 8344ELP, MegaRAID SAS 8408E, MegaRAID SAS 8480E, MegaRAID SAS 8708ELP, MegaRAID SAS 8888ELP, MegaRAID SAS 8880EM2, MegaRAID SAS 9260-8i - IBM ServeRAID M1015, ServeRAID M5014 These controllers support RAID 0, RAID 1, RAID 5, RAID 6, RAID 10, RAID 50 and RAID 60 using either SAS or SATA II drives. Although the controllers are actual RAID controllers, the driver makes them look just like SCSI controllers. All RAID configuration is done through the controllers' BIOSes. mfi supports monitoring of the logical disks in the controller through the bioctl(8) and envstat(8) commands. EVENTS
The mfi driver is able to send events to powerd(8) if a logical drive in the controller is not online. The state-changed event will be sent to the /etc/powerd/scripts/sensor_drive script when such condition happens. SEE ALSO
intro(4), pci(4), scsi(4), sd(4), bioctl(8), envstat(8), powerd(8) HISTORY
The mfi driver first appeared in NetBSD 4.0. BSD
March 22, 2012 BSD