Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Solaris 10 Speed and Duplex Settings: bge
Operating Systems Solaris Solaris 10 Speed and Duplex Settings: bge Post 302349297 by brialt1 on Monday 31st of August 2009 03:19:22 PM
Old 08-31-2009
Solaris 10 Speed and Duplex Settings: bge
Evening,

I am attempting to change the speed and duplex settings on a single interface on a bge card on an m3000 SPARC server. Currently the settings are as follows:

Code:
bge0            link: up        speed: 1000  Mbps       duplex: full
bge1            link: up        speed: 100   Mbps       duplex: half
bge2            link: up        speed: 1000  Mbps       duplex: full
bge3            link: unknown   speed: 0     Mbps       duplex: unknown
nxge0           link: down      speed: 1000  Mbps       duplex: full
nxge1           link: up        speed: 100   Mbps       duplex: full
nxge2           link: up        speed: 1000  Mbps       duplex: full
nxge3           link: down      speed: 1000  Mbps       duplex: full

I would like to change the bge1 interface to full duplex permanently. I read that I could make changes to the /platform/sun4u/kernel/drv/bge.conf file to make this permanent, however all of our attempts have not yielded the expected results.

Additional Information:

Code:
root@dssbfw101a.myhughesnet.com$ grep bge /etc/path_to_inst
"/pci@0,600000/pci@0/pci@1/pci@0/network@4" 0 "bge"
"/pci@0,600000/pci@0/pci@1/pci@0/network@4,1" 1 "bge"
"/pci@0,600000/pci@0/pci@2/pci@0/network@4" 2 "bge"
"/pci@0,600000/pci@0/pci@2/pci@0/network@4,1" 3 "bge"

Any assistance would be greatly appreciated.
Last edited by DukeNuke2; 08-31-2009 at 04:37 PM..
 

10 More Discussions You Might Find Interesting

1. Solaris

Duplex Settings

Hi All I've been having a lot of errors logged on the Cisco Catalyst (4000 series) which one of my Solaris servers is patched into. I have a feeling they are duplex related, but I'm a bit stuck as to how to confirm that. How do I: 1. Check the duplex settings on my eri0 card? 2. Set the... (3 Replies)
Discussion started by: saabir
3 Replies

2. IP Networking

NIC speed 100M/full duplex problem

I have a TOSHIBA AS7000 B150 Sun Box I wanted to run it with 100M/full duplex I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot. set eri:eri_adv_100fdx_cap=1 set eri:eri_adv_100hdx_cap=0 set eri:eri_adv_autoneg_cap=0 But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies

3. HP-UX

command to change duplex settings..

Hi Folks, I want the command to change the duplex settings of a HP-UX server. Thanks in advance. Sagar. (2 Replies)
Discussion started by: sag71155
2 Replies

4. Solaris

gigabit - fix speed/duplex on the switch ? or autoneg ?

Hi there We have a bit of a debate going here over what the prefered method is for setting 1000/Full on e1000g or nge interfaces is. As you aware the Solaris configration files for nge and e1000g dont allow you to "fix" 1000/Full but instead allow you to set auto-negotiate to ON but only... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

5. UNIX for Advanced & Expert Users

How to set full duplex for solaris 5.5

I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5. #ndd -set /dev/le adv_100fdx_cap 1 (6 Replies)
Discussion started by: csreenivas
6 Replies

6. Infrastructure Monitoring

How to find the duplex speed on Windows

Hi, In UNIX, it's very easy to find the duplex speed. But in Windows, is there a easy way to find the duplex speed? I can't go to over 100 servers to find this out, I was wondering if I run one command to do this? Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies

7. Solaris

How to find half duplex or full duplex

Hi, How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct? Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies

8. AIX

How to change Speed Duplex

How to change Speed Duplex ! How to change Speed Duplex by command chdev -P -l ent1 -a media_speed=1000_Full_Duplex How to change Speed Duplex by Smitty . smitty chgenet -> select adapter -> change Media speed etc. -> set "Apply change to DATABASE only" to yes -> Enter -> ... (0 Replies)
Discussion started by: ITHelper
0 Replies

9. AIX

Connected and Running with half duplex speed

VIO Server connected to switch port and running with half duplex speed on one of the shared ethernet adapter. We have verified at switch end and everythings looks good. Other ethernet adapter in the VIO server are connected and running in Full duplex speed. Please help me find why this shared... (4 Replies)
Discussion started by: mugunthanvh
4 Replies

10. Shell Programming and Scripting

Need script help for monitoring duplex settings

So I have a server I am trying to set up a script to send a Wall message notifying of my eth0 nic being set to 100 half duplex instead of 100 full duplex. I know I am trying to read from /etc/sysconfig/network/ifcfg-eth0 to pull the parameters STARTMODE=onboot BOOTPROTO=static... (6 Replies)
Discussion started by: lutador72
6 Replies

LEARN ABOUT NETBSD

tl

TL(4)							   BSD Kernel Interfaces Manual 						     TL(4)

NAME

     tl -- Ethernet driver for Texas Instruments ThunderLAN based board

SYNOPSIS

     tl* at pci? dev ? function ?

     Configuration of PHYs is necessary.  See mii(4).

DESCRIPTION

     The tl device driver supports network adapters based on the Texas Instruments ThunderLAN chip.

HARDWARE

     Supported cards include:

	   Compaq Netelligent
		   in baseboard and PCI variants (10BASE-T-only variant untested).

	   Compaq NetFlex 3/P
		   in baseboard variant only (the PCI variant doesn't use the same chip!).

	   It Baseboard Compaq Deskpro 4000 5233MMX Ethernet
		   (This has been tested on the Deskpro 4000M only).

	   TI TravelMate 5000 series laptop docking station's Ethernet board.

MEDIA SELECTION

     The different models of the supported boards come with some subset of RJ-45, BNC and AUI connectors.  Media selection is done using
     ifconfig(8) using the standard ifmedia(4) mechanism.  Refer to those manual pages for more information.

     The tl driver doesn't have full automatic media selection.  By default it will do an Nway (IEEE 802.3u) negotiation on the 10BASE-T port for
     the speed and duplex mode with the link partner.  If the AUI or BNC port is used, an explicit media type must be specified to ifconfig(8).

SEE ALSO

     ifmedia(4), mii(4), netintro(4), pci(4), ifconfig(8)

BUGS

     The board marked as untested will always claim having an AUI connector, where it may be a BNC one.

BSD
								   May 16, 2009 							       BSD
All times are GMT -4. The time now is 08:43 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy