08-28-2009
Quote:
Do I have to make all storage (about 3-5 TB / lpar) visible to all nodes or just to the nodes that are intended to takeover the resources.
You'll have to make storage visible for prod nodes and backup nodes of course so they can takeover in case.
So zoning and masking should assure following:
S1 can see disks of A1, A4, A5
S2 can see disks of A2, A3, A5.
But I don't know if a node can be in more than 1 cluster which would be the case for S1 and S2. I guess Shockneck will tell
Last edited by zaxxon; 08-28-2009 at 10:17 AM..
10 More Discussions You Might Find Interesting
1. AIX
Hi Guys,
I have two nodes clustered. Each node is AIX 5.2 & they are clustered with HACMP 5.2. The mode of the cluster is Active/Passive which mean one node is the Active node & have all resource groups on it & the 2nd node is standby.
Last Monday I noted that all resource groupes have been... (2 Replies)
Discussion started by: aldowsary
2 Replies
2. AIX
Hi
Can ony one advise which files can be deleted in /usr in an aix hacmp node ? Im new to aix and Im not sure which files can be deleted ?
#df -g /usr
Filesystem GB blocks Free %Used Iused %Iused Mounted on
/dev/hd2 7.00 1.00 86% 67013 22% /usr
... (4 Replies)
Discussion started by: samsungsamsung
4 Replies
3. AIX
This post just as a follow-up for thread https://www.unix.com/aix/115548-hacmp-5-4-aix-5300-10-not-working.html: there was a bug in the clcomdES that would cause the Two-Node-Cluster-Configuration-Assistant to fail even with a correct TCP/IP adapter setup. That affected HACMP 5.4.1 in combinatin... (0 Replies)
Discussion started by: shockneck
0 Replies
4. AIX
hi,
when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies
5. AIX
Hi,
I have a running HACMP Cluster with two nodes. Its working in active/passive mode. (i.e Out of the two nodes in the cluster one will be active and the other one will be on standby. If first node fails the other takes over)
1. There is a Service IP associated with the cluster. Now the... (2 Replies)
Discussion started by: aixromeo
2 Replies
6. AIX
Hi,
I have a IBM Power series machine that has 2 VIOs and hosting 20 LPARS.
I have two LPARs on which GPFS is configured (4-5 disks)
Now these two LPARs need to be configured for HACMP (PowerHA) as well.
What is recommended? Is it possible that HACMP can be done on this config or do i... (1 Reply)
Discussion started by: aixromeo
1 Replies
7. AIX
HACMP two-node cluster with mirrored LVM.
HACMP two-node cluster with two SAN storages mirrored using LVM. Configured 2 disk heartbeat networks - 1 per each SAN storage. While performing redundancy tests. Once one of SAN storage is down - cluster is going to ERROR state. What are the guidelines... (2 Replies)
Discussion started by: OdilPVC
2 Replies
8. AIX
Hello AIX experts,
I have few queries and appreciate if you could help me with them.
1. How to check if HACMP (or any other AIX OS cluster) is installed
2. How to check if HACMP (or any other AIX OS cluster) is running
3. how to check which Oracle DB instance is running on it
4. how to... (1 Reply)
Discussion started by: prvnrk
1 Replies
9. AIX
Folks,
Please have a look to the attached screenshot from my managed node's HEA configuration option page. I would like to know - what does "Flow Control Enabled" checkbox help us with if opted for?
Thanks!
-- Souvik (3 Replies)
Discussion started by: thisissouvik
3 Replies
10. AIX
Dear all
i have two aix system
-Model : P770
-OS version: AIX 6.1
-patch level : 6100-07-04-1216
-ha version : HACMP v 6.1.0.8
-host : A, B
last Wednesday, my B system suddenly went down with crash dump. after 1 minute, A system went down with crash dump. I checked the dump of A-system... (6 Replies)
Discussion started by: tomato00
6 Replies
LEARN ABOUT HPUX
cmdeleteconf
cmdeleteconf(1m) cmdeleteconf(1m)
NAME
cmdeleteconf - Delete either the cluster or the package configuration
SYNOPSIS
cmdeleteconf [-f] [-v] [-c cluster_name] [[-p package_name]...]
DESCRIPTION
cmdeleteconf deletes either the entire cluster configuration, including all its packages, or only the specified package configuration. If
neither cluster_name nor package_name is specified, cmdeleteconf will delete the local cluster's configuration and all its packages. If
the local node's cluster configuration is outdated, cmdeleteconf without any argument will only delete the local node's configuration. If
only the package_name is specified, the configuration of package_name in the local cluster is deleted. If both cluster_name and pack-
age_name are specified, the package must be configured in the cluster_name, and only the package package_name will be deleted. cmdelete-
conf with only cluster_name specified will delete the entire cluster configuration on all the nodes in the cluster, regardless of the con-
figuration version. The local cluster is the cluster that the node running the cmdeleteconf command belongs to.
Only a superuser, whose effective user ID is zero (see id(1) and su(1)), can delete the configuration.
To delete the cluster configuration, halt the cluster first. To delete a package configuration you must halt the package first, but you do
not need to halt the cluster (it may remain up or be brought down). To delete the package VxVM-CVM-pkg (HP-UX only), you must first delete
all packages with STORAGE_GROUP defined.
While deleting the cluster, if any of the cluster nodes are powered down, the user can choose to continue deleting the configuration. In
this case, the cluster configuration on the down node will remain in place and, therefore, be out of sync with the rest of the cluster. If
the powered-down node ever comes up, the user should execute the cmdeleteconf command with no argument on that node to clean up the config-
uration before doing any other Serviceguard command.
Options
cmdeleteconf supports the following options:
-f Force the deletion of either the cluster configuration or the package configuration.
-v Verbose output will be displayed.
-c cluster_name
Name of the cluster to delete. The cluster must be halted already, if intending to delete the cluster.
-p package_name
Name of an existing package to delete from the cluster. The package must be halted already. There should not be any
packages in the cluster with STORAGE_GROUP defined before having a package_name of VxVM-CVM-pkg (HP-UX only).
RETURN VALUE
Upon completion, cmdeleteconf returns one of the following values:
0 Successful completion.
1 Command failed.
EXAMPLES
The high availability environment contains the cluster, clusterA , and a package, pkg1.
To delete package pkg1 in clusterA, do the following:
cmdeleteconf -f -c clusterA -p pkg1
To delete the cluster clusterA and all its packages, do the following:
cmdeleteconf -f -c clusterA
AUTHOR
cmdeleteconf was developed by HP.
SEE ALSO
cmcheckconf(1m), cmapplyconf(1m), cmgetconf(1m), cmmakepkg(1m), cmquerycl(1m).
Requires Optional Serviceguard Software cmdeleteconf(1m)