05-29-2009
Add an appropriate route.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
Discussion started by: at_renai2001
5 Replies
2. UNIX for Dummies Questions & Answers
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies
3. Cybersecurity
I suspect that someone is using a sniffer on my Ethernet connection,
OS X 10.3.9, DSL,
ok, I'm in terminal using the "ifconfig" command >
flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384
right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
Discussion started by: su"do"er
1 Replies
4. UNIX for Advanced & Expert Users
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
7. AIX
Hello everyone
I have a problem with one server, has Aix 5.3 in the errpt has this message
IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION
F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE
EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN
F3931284 ... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
Route classifier in tc(8) Linux Route classifier in tc(8)
NAME
route - route traffic control filter
SYNOPSIS
tc filter ... route [ from REALM | fromif TAG ] [ to REALM ] [ classid CLASSID ] [ action ACTION_SPEC ]
DESCRIPTION
Match packets based on routing table entries. This filter centers around the possibility to assign a realm to routing table entries. For
any packet to be classified by this filter, a routing table lookup is performed and the returned realm is used to decide on whether the
packet is a match or not.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
from REALM
fromif TAG
Perform source route lookups. TAG is the name of an interface which must be present on the system at the time of tc invocation.
to REALM
Match if normal (i.e., destination) routing returns the given REALM.
EXAMPLES
Consider the subnet 192.168.2.0/24 being attached to eth0:
ip route add 192.168.2.0/24 dev eth0 realm 2
The following route filter will then match packets from that subnet:
tc filter add ... route from 2 classid 1:2
and pass packets on to class 1:2.
NOTES
Due to implementation details, realm values must be in a range from 0 to 255, inclusive. Alternatively, a verbose name defined in
/etc/iproute2/rt_realms may be given instead.
SEE ALSO
tc(8), ip-route(8)
iproute2 21 Oct 2015 Route classifier in tc(8)