04-05-2009
why do you need a monitor with a sun server? my 280 is two floors under me in the cellar cause it is to loud to be in my work room. all i need is a network line to the rsc card and to the onboard nic.
you can power on and off the server over the rsc and afterwards login to the server via ssh.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello all,
I'm lost and can't figure this problem out.
I have a Sun fire 280R running Solaris 8. Everything was working great. I have one drive in bay 1(not 0). But when I reboot the system it trys to open files in /dev/rdsk/c1t1d0s0. Should it have been opeing /dev/rdsk/c1t0d0s0, the... (4 Replies)
Discussion started by: larryase
4 Replies
2. Solaris
All,
After a power loss I went to power on our sun fire v120 that is running solaris 10 and now it will not boot. I tried power cycling it from the lom and pulling the cord but nothing works. All it does is after a power cycle it will start to boot and then start to spit out a bunch of hex... (2 Replies)
Discussion started by: jsandova
2 Replies
3. Solaris
Hello there!
I have Sun Fire 3800 with very old Solaris 9 and I need to perform upgrade to concurrent Solaris 10 version, preserving current OS configuration. I supose to make it using Live Upgrade, but according to Solaris Live Upgrade Software: Minimum Patch Requirements page, I need to... (5 Replies)
Discussion started by: Sapfeer
5 Replies
4. Solaris
Hi:
I bougth an used Sun Fire v440, and It have a firmware password. When I turn on the server, it ask for firmware password. (I don 't know what is the correct password). I can access to SC, but when I want to access to OBP, Firmware Password appears again. I remove the battery for two hours,... (1 Reply)
Discussion started by: mguazzardo
1 Replies
5. Emergency UNIX and Linux Support
Hi ,
during 2 weeks i´ve been trying to find them.
i need DCMU packets for managing internal disks on sun fire x4500 and sun fire x4600 on rhel. i have opened to tickets to myoraclesupport but no answer.
please anybody could tell me a link or anythiing?? i´ve been searching and searching... (1 Reply)
Discussion started by: pabloli150
1 Replies
6. Solaris
:)Dear Solaris Experts,
I need to clone a Solaris 10 x86 system using a ufsdump backup from the following source & target servers:
Sun Fire x2200 M2 with Quad Core Processor
# /usr/platform/`uname -i`/sbin/prtdiag
System Configuration: Sun Microsystems Sun Fire X2200 M2 with Quad Core... (8 Replies)
Discussion started by: gjackson123
8 Replies
7. Solaris
Hi,
I have a SUN Fire V440 server running Solaris 8. One of the 4 disks do not appear when issued the format command. The "ready to remove" LED is not on either.
Metastat command warns that this disk "Needs maintenace". Can I just shutdown and power off the machine and then insert an... (5 Replies)
Discussion started by: Echo68
5 Replies
8. Solaris
Hey Guys I am new here, dont know if any one can assist me with this issue.
I have a Sun-Fire-V490 machine that was upgraded to version 9 and patched a few months back.
Problem is a few network printers managed by the server is printing an extra page that comes out before and after every print... (0 Replies)
Discussion started by: mprogams
0 Replies
9. Solaris
cat note
Hi Sun Solaris Experts,
When I try to install Solaris 8 10/00 OS via the Solaris 8 Installation Disk on our Sun Fire V490 Server using the command , I get:
boot: cannot open kernel/sparcv9/unix
which means it can't find the unix kernel file on the installation disk .
By the way, I... (5 Replies)
Discussion started by: ssabet
5 Replies
10. Solaris
Hi Solaris/Unix Experts,
I've installed Oracle Solaris 10 1/13 on a Sun Fire V490 Server via its external Serial Port using a Cisco Console Cable connected to my Laptop PC running SecureCRT terminal emulation software emulating VT100 Terminal.
The Sun Fire V490 server has two on-board... (1 Reply)
Discussion started by: ssabet
1 Replies
LEARN ABOUT OPENSOLARIS
gvfs-monitor-file
gvfs-monitor-file(1) User Commands gvfs-monitor-file(1)
NAME
gvfs-monitor-file - monitor the change of a file using the VFS system
SYNOPSIS
gvfs-monitor-file URI
DESCRIPTION
gvfs-monitor-file monitors the change of a file using the VFS system.
OPERANDS
The following operands are supported:
URI Specifies the file location in standard URI format.
EXAMPLES
Example 1: Monitor a local file
example% gvfs-monitor-file file:///tmp/example
ENVIRONMENT VARIABLES
See environ(5) for descriptions of the following environment variables: NLSPATH.
EXIT STATUS
The exit value 0 is returned regardless of success or failure.
FILES
The following files are used by this application:
/usr/bin/gvfs-monitor-file Executable to monitor the change of a file using the VFS system.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWgnome-gvfs |
+-----------------------------+-----------------------------+
|Interface stability |Volatile |
+-----------------------------+-----------------------------+
SEE ALSO
gvfs-copy(1), gvfs-info(1), gvfs-less(1), gvfs-ls(1), gvfs-mkdir(1) gvfs-monitor-dir(1), gvfs-cat(1), gvfs-mount(1), gvfs-move(1), gvfs-
rename(1), gvfs-open(1), gvfs-rm(1), gvfs-save(1), gvfs-trash(1), gvfs-tree(1), attributes(5), environ(5)
NOTES
Written by Alvaro Lopez Ortega, Sun Microsystems Inc., 2008.
SunOS 5.11 25 Mar 2008 gvfs-monitor-file(1)