04-03-2009
Sun 6800 - SC's- neither are contactable!
Hi all
In a bit of a pickle here and need some help.
I have a 6800, with 2 SC controllers. I have a terminal concentrator ( TC ) attached to the serial ports. I cant ping / telnet these sc controllers, and when on the TC, I cant connect into them either. I am able to telnet to other servers on the switch / network, so switch is working.
I have rebooted the TC, and looks find, but I cant contact the damn SC controllers, either of them.
I cant get to them via either of the configured domains, like I could on a server with a alom / lom, using scadm / rscadm.
So, help ?? Can I just pull the pull lead out, and reboot one ??
Suggests oh wise fellow SA's ?
SBK
6 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Dear Sun gurus,
I have Sun Fire V240 server with its StorEdge 3300 disk-array. Following are its disks appeared in format command. I have prepared its partitions thru format and metainit & metattach (may be i have made wrong steps, causing the errors below because I have done thru some document... (1 Reply)
Discussion started by: shafeeq
1 Replies
2. UNIX for Dummies Questions & Answers
Hey there,
I am starting a Computer Science Foundation year at the end of this month and am trying to get a little bit ahead of the game. I have always wanted to learn Unix and am currently struggling with creating a boot disc to run Solaris (I have chosen to study this) from as opposed to... (0 Replies)
Discussion started by: Jupiter
0 Replies
3. Solaris
Good morning all
Once again, I come seeking wisdom :-)
I have a sunfire 6800 with two domains. Both Sc controllers are uncontactabe, probably due to network issues, but as the server is on a different site, Im a little stuck.
So, am trying to use scadm, as I know I can view / configure... (7 Replies)
Discussion started by: sbk1972
7 Replies
4. Solaris
I am new to Sun.
I brought Sun Fire 280R to practice UNIX. What are the requirements for the monitor/CRT? Will it burn out old non-Sun CRTs? Does it need LCD monitor?
Thanks. (3 Replies)
Discussion started by: bramptonmt
3 Replies
5. Solaris
d240 media tray(domain C) is which is connected to SUNFIRE 6800 (DOMAIN C),automatically restarting.remaining domains A and B are working fine..why i dont know..with out human intervention this domain is restarting automatically for 3 to 4 days in a day..plz solve this problem.why like this going... (4 Replies)
Discussion started by: tv.praveenkumar
4 Replies
6. Solaris
Hi all,
I have application running on sun server T5440 4x8x1.4 GHz, 64 GB RAM, application running very slow though load average too low. when I install my application on another server SUN M3000 (One CPU 1x8x2.5GHz, 8GB RAM), application run smoothly.
Here is my server T5440 info:
... (6 Replies)
Discussion started by: insatiable1610
6 Replies
LEARN ABOUT NETBSD
hptide
HPTIDE(4) BSD Kernel Interfaces Manual HPTIDE(4)
NAME
hptide -- Triones/Highpoint IDE disk controllers driver
SYNOPSIS
hptide* at pci? dev ? function ? flags 0x0000
DESCRIPTION
The hptide driver supports the Triones/Highpoint HPT366, HPT370, HPT370A, HPT372 and HPT374 IDE controllers, and provides the interface with
the hardware for the ata(4) driver.
The 0x0002 flag forces the hptide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO
ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
BUGS
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD
October 8, 2003 BSD