Sponsored Content
Operating Systems Solaris T5240 and Internal SAS RAID Configuration help Post 302299751 by nicktrix on Saturday 21st of March 2009 07:07:49 AM
Old 03-21-2009
Thanks DukeNuke.. I will use that bootable cd... If I face any difficulty I will inform... I have found that bootable Live CD in given link.... It's latest I think
http://downloadcenter.intel.com/filter_results.aspx?strTypes=all&ProductID=2875&OSFullName=Solaris*〈=eng&strOSs=33&submit=Go!
 

10 More Discussions You Might Find Interesting

1. AIX

regd raid 0 configuration

Hey Alll Thanks for the help u give me yesterday,i need a help again from u all guys i have RS 6000 server with AIX 4.3.3 OS and with external storage (multipack) with 12 Hard disk drive which will be connected to RS 6000 scsi controller ,i dont have any raid card. now i have to... (0 Replies)
Discussion started by: solaris8in
0 Replies

2. SCO

driver needed for hp smartarry p200i sas raid controller

recently we have purchased hp proliant ml350 g5 server and configured raid 5 with hp smartarray p200i sas controller.but i could not found any sas raid controller hp smartarry p200i driver for sco unix 5.0.7 :(.i searched on hp support site,but no use.any one can help. (3 Replies)
Discussion started by: prakrithi
3 Replies

3. Solaris

istall sas raid HBA internal card

I need to install a raid HBA internal card on a T5240. The reason is I have more drives and the current mother board controller does not support more than 4 drives. My question is I have raidctl set up on current drives. If I install new HBA card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies

4. Solaris

Install Solaris 10 with an internal StorageTek SAS HBA Raid card

Hi all i would like to ask some suggests about my next job! I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid. The problem come in if every disk is now controlled by the HBA, how can I install the OS? No disk is being detected by the OS. SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies

5. Solaris

installing solaris with StorageTek SAS RAID Internal HBA

i was given a task which needs to perform a raid 1 on the boot disk, and 4 other disks on raid 10. Is there any other alternative in installing solaris 10 other than through network installation?will be using solaris update 6. while reading through the user guide i got pretty confuse. ... (1 Reply)
Discussion started by: monstar1407
1 Replies

6. Red Hat

Software RAID configuration

We have configured software based RAID5 with LVM on our RHEL5 servers. Please let us know if its good to configure software RAID on live environment servers. What can be the disadvantages of software RAID against hardware RAID (4 Replies)
Discussion started by: mitchnelson
4 Replies

7. AIX

Internal PCI X RAID Controller issue ?

Hello folks, Could someone tell me why I unable to create pdisks for a RAID Array # lscfg | grep scsi + sisscsia0 U787A.001.DPM0707-P1 PCI-X Dual Channel Ultra320 SCSI Adapter + scsi0 U787A.001.DPM0707-P1-T10 PCI-X Dual Channel Ultra320 SCSI Adapter... (12 Replies)
Discussion started by: filosophizer
12 Replies

8. Solaris

Cannot configure RAID on T5240

Hi ! I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before. I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl. ... (2 Replies)
Discussion started by: delavega
2 Replies

9. Red Hat

RAID Configuration for IBM Serveraid-7k SCSI RAID Controller

Hello, I want to delete a RAID configuration an old server has. Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton? I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies

10. AIX

Replaced pdisk not showing up in SAS Disk Array Configuration

OSLevel: 5300-10-02-0943 System Model: IBM,8203-E4A Power 6 == Hi! I replaced a failed pdisk in the raid enclosure as follows, - rmdev -l 'pdisk18' '-d' - Replaced it. - cfgmgr (detected) - I can see the new drive, with the correct serial # lscfg -v -l pdisk18 pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
mkcd(1M)						  System Administration Commands						  mkcd(1M)

NAME
mkcd - create bootable Solaris ISO image SYNOPSIS
/usr/bin/mkcd -v [-l label] media-root iso DESCRIPTION
The mkcd utility takes media-root (the root of an on-disk Solaris install media) as input and creates a bootable Solaris ISO image in the file iso, using mkisofs(8). The file can then be burned onto a CD/DVD with utilities such as cdrw(1) or cdrecord(1). (Neither mkisofs(8) nor cdrecord(1) are SunOS man pages.) Caution - The directory tree media-root must contain the file boot/grub/stage2_eltorito, which will be written to the media boot sectors. This file will be modified with some boot information, thus it must be writable. If necessary, first save a copy prior to running this utility. OPTIONS
The following options are supported: -l label Sets label as the label/volume name of the ISO image. -v Verbose. Multiple -v options increase verbosity. OPERANDS
The following operands are supported: media-root Top-level directory of an on-disk Solaris install media. iso Name of the output file which will contain the resulting ISO image. EXAMPLES
Example 1 Creating an ISO Image and Burning a CD/DVD The following commands create an ISO image from the content of s10u1 and burn the image to a CD/DVD. # /usr/bin/mkcd s10u1 s10u1.iso # /usr/bin/cdrw -i s10u1.iso ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ |Interface Stability |Committed | +-----------------------------+-----------------------------+ SEE ALSO
cdrw(1), attributes(5) mkisofs(8), (/usr/share/man/man8/mkisofs.8), in the SUNWfsman package (not a SunOS man page) SunOS 5.11 25 Jul 2008 mkcd(1M)
All times are GMT -4. The time now is 08:33 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy