03-02-2009
are you using sol10 x86? can you verify the hardware is compatible with the HCL ??
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Pls help
i've used the boot assistance disk to boot my computer (P3 300)
after checking the drivers , i select the CD to install , however,
the computer said it can't mount the CD
CD is download from sun.com (solaris 8)
my CD rom is Misabushi and Ricoh (7060) ,
both cannot do so,
what is... (4 Replies)
Discussion started by: kazamih
4 Replies
2. IP Networking
I have just installed solaris 8 for Intel on one of my machines at home and I have a cable modem connection with a static IP and I am using a linksys cable/dsl router to assign IP's to my machines. I was wondering if any of you guys know the specific files and examples of the files I have to... (2 Replies)
Discussion started by: reggie316
2 Replies
3. UNIX for Advanced & Expert Users
hi.
Have anyone use kde for solaris, if so can you help me download and configure it. i don't know which files i should download for solaris because there lots of files. Could you point me to the right path.thanks in advance. (9 Replies)
Discussion started by: souldier
9 Replies
4. Programming
hi I'm looking for a C Compiler that will run on a Solaris 8 (Intel) platform and that doesn't need to be complied.
I've tried gcc binaries but they don't seem to work.
Thanx. (5 Replies)
Discussion started by: ianf
5 Replies
5. UNIX for Dummies Questions & Answers
Do you now have to pay to download the Solaris 8 OE? If so when did they change it? (3 Replies)
Discussion started by: tycobb
3 Replies
6. UNIX for Advanced & Expert Users
I was wondering what features are not available on Solaris installed on Intel architecture as compared to the SPARC archietecture??
:-) (3 Replies)
Discussion started by: encrypted
3 Replies
7. Solaris
Hello all mentor.
I am a new in this furom and also just self studying unix environment. :confused:
I have installed intel solaris 9 in my laptop and i have forgotten the root password nor maybe the numlock or capslock of the keyboard was enabled
during I enter the password installation... (3 Replies)
Discussion started by: eykyn17
3 Replies
8. Solaris
Hi All,
How can I go to OBP on Solaris 10-intel? I tried doing ctrl+c or ctrl+break, it won't go to the "ok" prompt.
Thanks in advance,
itik (6 Replies)
Discussion started by: itik
6 Replies
9. UNIX for Advanced & Expert Users
I am beginner to os world.
Is OS dependent on hardware()? i guess yes. then how linux get install on intel as well as other processors?
Is there any unix os for intel processors? (3 Replies)
Discussion started by: meet2kris
3 Replies
10. SCO
hi
I have a fresh installation of SCO 5.0.6 and I have download a NIC driver for Intel Pro 1000:
ftp://ftp.sco.com/pub/openserver5/507/drivers/eeG_5.0.7g/VOL.000.000
Howto install it using floppy?
---------- Post updated at 04:02 PM ---------- Previous update was at 02:18 PM... (0 Replies)
Discussion started by: ccc
0 Replies
LEARN ABOUT CENTOS
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)
NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [ -a blkno [blkno...]] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option
cannot be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 addbadsec(1M)