02-20-2009
Quote:
Originally Posted by
Sprellarinn
Hi.
Just use the standard AIX LVM tools. The old HDD is probably called hdisk0 (see by issuing lspv) and if you simply insert the new one you will have hdisk1 (etc) for that one. Then extend the volume group and issue migratepv command. If this is a rootvg disk you will need to do bosboot & bootlist commands and your done.
Thanks I will try that.
However what about the jumper settings, going off of memory the current hard drive is using the 2nd from the far end near the corner of the hard drive. which is SCSI ID BIT 2 connecting it to ground? On the new hard drive should the jumpers match when connecting to the PC. or should it be different?
Thanks again
10 More Discussions You Might Find Interesting
1. HP-UX
Hi,
My HP-UX has some errors to wake up and one of them are:
/dev/vg00/rlvol4 BAD CYLINDER GROUPS
I have thought that my hdd has physical problems, my question is:
Exists a program to check the hdd physically and to repair it...
Thanks.... (0 Replies)
Discussion started by: efrenba
0 Replies
2. UNIX for Dummies Questions & Answers
I am adding a new HDD to a Unix Sco Release 5 webserver.
I consider myself a windows pro. However, growing up in the late 90's means I have little Unix knowledge. I know the HDD has to be mounted and formatted correctly. Can anyone give me any advice on this?
A dummy's guide to installing a... (5 Replies)
Discussion started by: jeffreydavisjr
5 Replies
3. UNIX for Dummies Questions & Answers
i have this HDD with SCO 5.0.6 and i'm getting this errors
WARNING: wd0: Error on fixed disk dev 1/42, block=4829, cmd=0x000000C8
Sun Mar 11 05:50:08 2007
status=0x00000040, LBA sector=1285723, cylinder/head=5022/0
WARNING: wd0: Error... (0 Replies)
Discussion started by: josramon
0 Replies
4. UNIX for Dummies Questions & Answers
Hi,
my router is my Linux embedded device.
I have system installed on HDD 4GB usb stick, part1 swap, part2 /opt , part3 data.
I need to copy my system to new HDD 8GB usb stick.
What is a way for 4GB > 4GB HDD
and what for 4GB > 8GB
As I remeber, I can copy image of my 4GB HDD usb stick... (7 Replies)
Discussion started by: jack2
7 Replies
5. Solaris
All,
I am a complete grasshopper when it comes to Unix, so here goes. I have a Solaris 9 server, running two 36GB HDD in a mirrored configuration. I am running low on disk space, and have purchased an additional 145GB HDD. Can anyone point me in the direction to some documentation on how to... (1 Reply)
Discussion started by: ptvenom427
1 Replies
6. UNIX for Dummies Questions & Answers
I have a Sun Blade 1500 (sparc)
I have two HDD's both configured with Solaris 10.
How do I chose at boot which HDD I want to use?
I've had a look through the FAQ, also done a web search but haven't come up with requisite info.
touch /reconfigure does not seem to help.
Any suggestions... (8 Replies)
Discussion started by: lewtargett
8 Replies
7. UNIX for Dummies Questions & Answers
i just got a copy of windows and when i go to install it, it says i cant because it needs an ntfs file system. can anyone help me format my hard drive through linux? (2 Replies)
Discussion started by: camroc84
2 Replies
8. Solaris
Hi All
Please can I have some help/advice.
I am fairly new to unix so any help will be useful.
I need to perform HDD Mirroring on a Sun Fire V245 Server running Solaris 10 OS.
The system is already up and running and has the partitions and slices already.
Is it possible to perform the... (6 Replies)
Discussion started by: pluto.flame
6 Replies
9. UNIX for Dummies Questions & Answers
I need to get an external HDD for a SUN server running Solaris 10. The Western Digital that I have will not recognize and when I went looking for drivers WD only has them for MAC and Windows. Is there a External HDD that is known to work with Unix? (24 Replies)
Discussion started by: SIFT3R
24 Replies
10. AIX
Hi Folks,
I am facing an issue with the performance.
P4 with 1 processor and 16 GB RAM and SAN HDD = Oracle report takes 25 minutes
P5 with 2 processors and 16 GB RAM internall HDD with LPAR = Oracle Report takes 1 hour 15 minutes ( please note I have assigned all the max processors and... (7 Replies)
Discussion started by: filosophizer
7 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
mknod(1), chown(1), mount(8), sd(4)
Linux 1992-12-17 HD(4)