01-06-2009
have you tried another nic on the server in the same switch/port/config? you could have a bad nic. also, have you checked w/ your network team on how the switch port is configured?
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
Discussion started by: at_renai2001
5 Replies
2. UNIX for Dummies Questions & Answers
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies
3. Cybersecurity
I suspect that someone is using a sniffer on my Ethernet connection,
OS X 10.3.9, DSL,
ok, I'm in terminal using the "ifconfig" command >
flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384
right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
Discussion started by: su"do"er
1 Replies
4. UNIX for Advanced & Expert Users
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
7. Solaris
my solris box network is unreachable how to solve this
ipaddress assiagning and entry in vi /etc/host
how to solve network is unreachable (2 Replies)
Discussion started by: tirupathi
2 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
LEARN ABOUT OPENSOLARIS
scconf_transp_adap_ge
scconf_transp_adap_ge(1M) System Administration Commands scconf_transp_adap_ge(1M)
NAME
scconf_transp_adap_ge - configure the Gigabit Ethernet (ge) transport adapter
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
You can configure ge adapters as cluster transport adapters. These adapters can only be used with transport type dlpi.
The ge adapter connects to a transport switch or to another ge adapter on a different node. In either case, the connection is made through
a transport cable.
When a transport switch is used and the endpoints of the transport cable are configured using scconf, scinstall, or other tools, you are
asked to specify a port name on the transport switch. You can provide any port name, or accept the default, as long as the name is unique
for the switch.
The default is to set the port name to the node ID hosting the adapter at the other end of the cable.
There are no user configurable properties for cluster transport adapters of this type.
SEE ALSO
clinterconnect(1CL), clnode(1CL), scconf(1M), scinstall(1M), ge(7D)
Sun Cluster 3.2 4 May 2006 scconf_transp_adap_ge(1M)