11-05-2008
iptables may block icmp requests
try to reset the routing table on both sides
can you ping the default gateway from the 192.168.2.0 net, if there is one from one side?
switch/router may block different ip adresses too, check acls
10 More Discussions You Might Find Interesting
1. Solaris
I need to add a PCI NIC to a sunblade 100 running solaris 8. Im new to this and was hoping someone could give me some card names and models which will work for this system and has a driver for this sparc system.
thanks (3 Replies)
Discussion started by: meyersp
3 Replies
2. IP Networking
Hi;
I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now... (2 Replies)
Discussion started by: texaspanama
2 Replies
3. High Performance Computing
Hello
I have 2 machines with 3 NIC cards.
When I setup veritas, I receive this message:
e1000g1 has an IP address configured on it. It could be a public NIC on ken.
Are you sure you want to use e1000g1 for the first private heartbeat link?
As if e1000g1 should not have an IP address.... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies
4. HP-UX
I am running HP_UX 11.23 with 4 NIC cards (this is our TSM server)
I have 4 subnets we are backing across. trying to keep traffic on their subnets. I only have one route statment should I add more.
route add net 123.99.8.0 netmask 255.255.255.0 123.99.8.254
route add net 123.99.67.0 netmask... (2 Replies)
Discussion started by: myork
2 Replies
5. HP-UX
Hello,
I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches.
On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular... (1 Reply)
Discussion started by: ldaliosmane
1 Replies
6. IP Networking
Hi,
What is the best reference that gives in detail on nic cards configuration , assigning multiple ip addresses to a single interface, netlink library etc and all basic stuff at this level..?
Thanks (2 Replies)
Discussion started by: Gopi Krishna P
2 Replies
7. Red Hat
Ok, Im trying to get NFS working on my RHEL 5 box, apparently i can use the box as a client, but not as a server. If it helps i cant ssh into the box (server), but as a client ssh works fine. Ive configured
server:
/etc/hosts.allow:
all : all
all :all@all
setup my /etc/exports file... (4 Replies)
Discussion started by: drs.grid
4 Replies
8. Ubuntu
I found an old post that talks about 2 nice cards and it is driven by the IP address .... but I didn't understand it because the 2 people skipped information for me the newbie..
Can someone help me... I have the proxy server setup and I believe I have enabled the 2nd nic card, I just need one... (1 Reply)
Discussion started by: trilju2005
1 Replies
9. Ubuntu
I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table?
I don't know how to do this.:confused: (9 Replies)
Discussion started by: trilju2005
9 Replies
10. Red Hat
I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch.
The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Discussion started by: tjcooper
0 Replies
AN(4) BSD Kernel Interfaces Manual AN(4)
NAME
an -- Aironet 4500/4800 and Cisco 340/350 series wireless network driver
SYNOPSIS
an* at pcmcia? function ?
an* at pci? dev ? function ?
an* at isapnp?
DESCRIPTION
The an driver provides support for Aironet Communications 4500/4800 and Cisco Aironet 340/350 series wireless network adapters. This
includes the ISA, PCI and PCMCIA varieties. The 4500 series adapters operate at 1 and 2Mbps while the 4800 series and 340/350 series can
operate at 1, 2, 5.5 and 11Mbps. The ISA, PCI and PCMCIA devices are all based on the same core PCMCIA modules and all have the same pro-
gramming interface, however unlike the Lucent WaveLAN/IEEE cards, the ISA and PCI cards appear to the host as normal ISA and PCI devices and
do not require any PCMCIA support.
The PCMCIA Aironet cards require PCMCIA support. ISA cards can either be configured to use ISA Plug and Play or to use a particular I/O
address and IRQ by properly setting the DIP switches on the board. (The default switch setting is for plug and play.) The an driver has
Plug and Play support and will work in either configuration, however when using a hard-wired I/O address and IRQ, the driver configuration
and the NIC's switch settings must agree. PCI cards require no switch settings of any kind and will be automatically probed and attached.
All host/device interaction with the Aironet cards is via programmed I/O. The Aironet devices support 802.11 and 802.3 frames, power manage-
ment, BSS (infrastructure) and IBSS (ad-hoc) operation modes. The an driver encapsulates all IP and ARP traffic as 802.11 frames, however it
can receive either 802.11 or 802.3 frames. Transmit speed is selectable between 1Mbps, 2Mbps, 5.5Mbps, 11Mbps, or ``auto'' (the NIC automat-
ically chooses the best speed).
By default, the an driver configures the Aironet card to join an access point with an SSID of null string. For ad-hoc mode, in which sta-
tions can communicate among each other without the aid of an access point, the driver must be set using ifconfig(8).
For more information on configuring this device, see ifconfig(8) and ifmedia(4).
HARDWARE
Cards supported by the an driver include:
Aironet 4500 Series
Aironet 4800 Series
Cisco Aironet 340 Series
Cisco Aironet 350 Series
DIAGNOSTICS
an%d: init failed The Aironet card failed to come ready after an initialization command was issued.
an%d: failed to allocate %d bytes on NIC The driver was unable to allocate memory for transmit frames in the NIC's on-board RAM.
an%d: device timeout The Aironet card failed to generate an interrupt to acknowledge a transmit command.
SEE ALSO
arp(4), ifmedia(4), netintro(4), ifconfig(8)
HISTORY
The an device driver first appeared in FreeBSD 4.0, and then in NetBSD 1.6.
AUTHORS
The an driver was written by Bill Paul <wpaul@ee.columbia.edu>.
BSD
December 13, 2000 BSD