Sponsored Content
Full Discussion: interface may off
Operating Systems Solaris interface may off Post 302187594 by pupp on Monday 21st of April 2008 01:44:29 PM
Old 04-21-2008
is bge3 going to a switch or router?
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. Solaris

no such interface

Hi Community, I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output: # ifconfig hme0 <ip_address> netmask <mask> plumb #ifconfig: plumb: hme0: no such interface I've the same thing with dhcp service. could you provide any solution... (1 Reply)
Discussion started by: Sunb3
1 Replies

3. IP Networking

How to down interface without name

Hi, ifconfig -a return: eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0 ... (5 Replies)
Discussion started by: djbuly
5 Replies

4. UNIX for Advanced & Expert Users

interface problem

hi all, i have problem with my box, until now i can't investigate the root cause of my issue at my box. here the problem. i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies

5. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

6. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

7. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

8. UNIX for Dummies Questions & Answers

Interface

Hi All, How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
defaultrouter(4)                                                   File Formats                                                   defaultrouter(4)

NAME
defaultrouter - configuration file for default router(s) SYNOPSIS
/etc/defaultrouter DESCRIPTION
The /etc/defaultrouter file specifies a IPv4 host's default router(s). The format of the file is as follows: IP_address ... The /etc/defaultrouter file can contain the IP addresses or hostnames of one or more default routers, with each entry on its own line. If you use hostnames, each hostname must also be listed in the local /etc/hosts file, because no name services are running at the time that defaultrouter is read. Lines beginning with the ``#'' character are treated as comments. The default routes listed in this file replace those added by the kernel during diskless booting. An empty /etc/defaultrouter file will cause the default route added by the kernel to be deleted. Use of a default route, whether received from a DHCP server or from /etc/defaultrouter, prevents a machine from acting as an IPv4 router. You can use routeadm(1M) to override this behavior. FILES
/etc/defaultrouter Configuration file containing the hostnames or IP addresses of one or more default routers. SEE ALSO
in.rdisc(1M), in.routed(1M), routeadm(1M), hosts(4) SunOS 5.10 17 Aug 2004 defaultrouter(4)
All times are GMT -4. The time now is 07:58 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy