|
|
Sponsored Content
Special Forums
IP Networking
NIC speed 100M/full duplex problem
Post 302158706 by DukeNuke2 on Wednesday 16th of January 2008 05:43:46 AM
01-16-2008
|
|
9 More Discussions You Might Find Interesting
1. Programming
what is meant by full duplex and half duplex?
b'coz in differences b\w hub and switch ,i heard lot this duplex word
so please help me (1 Reply)
Discussion started by: parvathy
1 Replies
2. Solaris
Hi all,
I tried to use this command
ndd -set /dev/eri adv_1000fdx_cap 1
but i get a "operation failed, Invalid argument"
anyone can help ? Thanks (5 Replies)
Discussion started by: DarReNz
5 Replies
3. Solaris
Hi there
We have a bit of a debate going here over what the prefered method is for setting 1000/Full on e1000g or nge interfaces is.
As you aware the Solaris configration files for nge and e1000g dont allow you to "fix" 1000/Full but instead allow you to set auto-negotiate to ON but only... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
4. Infrastructure Monitoring
Hi,
In UNIX, it's very easy to find the duplex speed. But in Windows, is there a easy way to find the duplex speed? I can't go to over 100 servers to find this out, I was wondering if I run one command to do this?
Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies
5. Solaris
Evening,
I am attempting to change the speed and duplex settings on a single interface on a bge card on an m3000 SPARC server. Currently the settings are as follows:
bge0 link: up speed: 1000 Mbps duplex: full
bge1 link: up speed: 100 Mbps ... (13 Replies)
Discussion started by: brialt1
13 Replies
6. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
7. AIX
How to change Speed Duplex !
How to change Speed Duplex by command
chdev -P -l ent1 -a media_speed=1000_Full_Duplex
How to change Speed Duplex by Smitty .
smitty chgenet -> select adapter -> change Media speed etc. -> set "Apply change to DATABASE only" to yes -> Enter -> ... (0 Replies)
Discussion started by: ITHelper
0 Replies
8. AIX
VIO Server connected to switch port and running with half duplex speed on one of the shared ethernet adapter. We have verified at switch end and everythings looks good.
Other ethernet adapter in the VIO server are connected and running in Full duplex speed.
Please help me find why this shared... (4 Replies)
Discussion started by: mugunthanvh
4 Replies
9. Solaris
Hi All
I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only.
Please also let me know how to do it online through command.
regards (0 Replies)
Discussion started by: amity
0 Replies
LEARN ABOUT NETBSD
url
URL(4) BSD Kernel Interfaces Manual URL(4) NAME
url -- Realtek RTL8150L USB Ethernet driver SYNOPSIS
url* at uhub? urlphy* at mii? DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip. The url driver supports the following adapters: CompUSA USBKR100 GreenHouse GH-USB100B Melco Inc. LUA-KTX Sitecom LN013 For more information on configuring this device, see ifconfig(8). DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8) HISTORY
The url device driver first appeared in NetBSD 1.6. AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>. BSD
September 18, 2006 BSD