Below is what i intend to do.
1. I stored some data in a file.
2. I intend to read the file line by line and store each line of data into a variable, so that i can used it later.
In a shell that has arrays (e.g., bash, ksh93):
Code:
IFS='
'
file=( $( cat "$FILE" ) )
However, that will probably be no better than reading the file when you need it.
If you need to store it in variables that depend on the contents of each line:
Code:
while IFS= read -r line
do
## check for criteria and store in variable here
done < "$FILE"
Dear friends,
i am writing csh script
i have one dat file containing following data.like this.
08FD3 03A26 000FA0 FFFF0 BBA0F 00000 00000
from the above file i want to read each letter and store it in one variable.
how it is possible.
please help (7 Replies)
Hi,
How to read a file and put the values in a script. E.g.
file1.txt
02/12/2009;t1;t2
The script should read this file and put these values in 3 different variables x1,x2,x3 which can be used further.
Thanks
Ashu (3 Replies)
Friends,
I have a file output.txt with values as below:
092307135717
061910135717
I want to know how to read this file and then assign each value to a variable.
say like
var1=092307135717
var2=061910135717
So that I can use this VAR1 and Var2 in the shell script for further processing.... (3 Replies)
Hi Gurus,
I am trying for a scenario where in I want to read the contents of a file line by line and then store them in variables. Below is the script:
#!/bin/ksh
while read line
do
id=`echo $line | cut -f1 -d |`
name=`echo $line | cut -f2 -d |`
echo $id
... (11 Replies)
Hello, I am quite new in shell scripting and I would like to write a little scritp to run a program on some parameters files.
all my parameters files are in the same directory, so pick them up with
ls *.para >>dirafter that I have a dir file like that:
param1.para
param2.para
etc...
I... (2 Replies)
Hi,
I would like to read a file line by line and then store the whole line word by word in array so that I can do specific manipulation on each word.
$ cat test.txt
hello how are you
i am good
I would like to have an array created dynamically so that first time , the... (4 Replies)
Hi,
I have a file service.xml which has following content:
<?xml version="1.0" encoding="UTF-8"?>
<Service Ver="2.31.13"/>
I want to read the value of Ver (that is 2.31.13) and assign to a variable which i further use.
Please help me in that. (3 Replies)
Hello,
I am using below code for reading from a file and assigning the values to a variable , but it is loosing the value after the loop , please suggest to retain the value of the variable after the loop ,
while IFS=: read -r line
do
set $dsc=$line
echo 'printing line variable ' $line... (1 Reply)
Discussion started by: ParthThakkar
1 Replies
LEARN ABOUT NETBSD
url
URL(4) BSD Kernel Interfaces Manual URL(4)NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO arp(4), mii(4), netintro(4), usb(4), ifconfig(8)HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD September 18, 2006 BSD