07-18-2006
It is fully documented in the guide (for each version) on
http://docs.sun.com including examples.
9 More Discussions You Might Find Interesting
1. Solaris
Hello,
I am trying to do mirror in solaris 9. I have total 0-7 disks
4 5 6 7
0 1 2 3
Drive 0 and Drive 4 = Boot Drives
Need to Mirror following drives.
Drive 1 and Drive 5 = Need to mirror
Drive 1 was mounted on: /prod1, /prod2, /prod3, /prod4, /prod5.
Then i... (3 Replies)
Discussion started by: deal732
3 Replies
2. Solaris
Hi All,
How do I break the solaris 8 mirror? And how do I make sure I will point the first hd mirror on reboot.
If the first break mirror won't boot. How do I make the copy mirror to boot?
Thanks in advance,
itik (2 Replies)
Discussion started by: itik
2 Replies
3. Solaris
Hi everyone,
Normally it always easier in Sparc machine, i can set or manually use the boot-device in NVram to boot the mirrored disk. However I have a big trouble about x86 mirror for a long time. I have been doing anything i can: search document, google, ask the others.
Recently i did as... (5 Replies)
Discussion started by: tien86
5 Replies
4. Solaris
hi,
I'm newbie in Solaris 10. can someone explain me the steps of how to create mirror disk in Solaris machine.
thanks in advance (5 Replies)
Discussion started by: Wong_Cilacap
5 Replies
5. Solaris
I’m setting up a boot disk mirror on Solaris 10 x86. I’m used to doing it on SPARC, where you can copy the partition table using fmthard. My x86 boot disk has 2 primary partitions, a Solaris one and a diagnostic one. Is there a way to copy those 2 primary partitions to the second disk without... (6 Replies)
Discussion started by: TKD
6 Replies
6. Solaris
hi friends, need help.. it is my first time patching using mirror disk backup approach, not so sure about the steps :confused: how do you detach, patch it, boot it and reattach it ? any kind soul here can advise ? thanks in advance..:)
below is the information from my machine:
Filesystem ... (3 Replies)
Discussion started by: Exposure
3 Replies
7. Solaris
Dear All
I have question and I want some one to answer it ..
in Solaris 10 I have two mirrors as below .. c3t0d0s0 & c3t1d0s0
NAME STATE READ WRITE CKSUM
rpool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
... (1 Reply)
Discussion started by: top.level
1 Replies
8. HP-UX
what is the difference between DRD and Root Mirror Disk using LVM mirror ? (3 Replies)
Discussion started by: maxim42
3 Replies
9. Solaris
We have Proliant DL380 G2 running Solaris 9 x86
There are 6 physical disks installed which I believe are mirrored at hardware level to 3 sets to present 3 disks to the OS.
Is there any way to check the mirror status at OS level ?
I am guessing not and it may need a trip to site as we have no... (4 Replies)
Discussion started by: frustrated1
4 Replies
LEARN ABOUT NETBSD
urlphy
URL(4) BSD Kernel Interfaces Manual URL(4)
NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8)
HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
September 18, 2006 BSD