Sponsored Content
Operating Systems AIX hacmp network adapter re-define Post 302073747 by johnf on Wednesday 17th of May 2006 09:10:27 AM
Old 05-17-2006
Don't worry solved it. Delete the ent devices with rmdev and then reconfigure the defined device with correct IP address. Make sure HACMP is down on the node before hand. When the adapters are back with the correct addresses restart HACMP. Done!
 

10 More Discussions You Might Find Interesting

1. Solaris

Sun v440/v880 network adapter teaming

Is it possible to team two network adapters for fault tolerance in a Sun v440 or v880 Solaris 8 box? If so how would I go about doing so? (1 Reply)
Discussion started by: ghuber
1 Replies

2. IP Networking

define IP protocols on network

what method would I use to determine which IP protocols network (0 Replies)
Discussion started by: mar mar
0 Replies

3. AIX

change network adapter

hello i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 ) what i need to do after the new adapter installed on the machine? thanks best regards ariec (1 Reply)
Discussion started by: ariec
1 Replies

4. AIX

How to active this network adapter?

When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command: entstat -all ent#|grep -i priority Priority: 5 Active: False How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies

5. UNIX for Dummies Questions & Answers

External Network Adapter for Solaris 10

Hi All, I am new here - this is my first post. I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies

6. AIX

HACMP: set preferred adapter for service ip

Hi, lets say we have two boot interfaces en0 en1 and two resource groups, with two service ips, sip1 and sip2, one persistent ip pers1 both persistend and service ips are applied as ip-alias when I start the cluster, and bring the resource groups up, it looks like en0: sip1 and sip2 ... (4 Replies)
Discussion started by: funksen
4 Replies

7. UNIX for Dummies Questions & Answers

SCO Unixware 7.1.4 Network Adapter Error

Hi All I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached. I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies

8. UNIX for Dummies Questions & Answers

Simulated driver for Network Interface Adapter

Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean? - It has to run on all network adapters - It has to be as simple as it can be - It has to run on all linux distributions (or at least most of them) - It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies

9. Hardware

Problematic RTL8188EE Wireless Network Adapter

Good Day All, There are numerous results when searching google on this issue, however, none seem to have a solution. I have read until my eyes bleed and banged my head on the table more than once! :) I am hoping to resolve this issue -- or at least have a decent workaround. It is a real... (13 Replies)
Discussion started by: RogerBaran
13 Replies

10. SCO

Can not recognize network adapter SCO UNIX in HP z400

hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback. show message : dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
bt-audio(1)							    bluez-tools 						       bt-audio(1)

NAME
bt-audio - a bluetooth generic audio manager SYNOPSIS
bt-audio [OPTION...] Help Options: -h, --help Application Options: -a, --adapter=<name|mac> -c, --connect=<name|mac> -d, --disconnect=<name|mac> DESCRIPTION
This utility is used to manage outgoing audio service connections. OPTIONS
-h, --help Show help -a, --adapter <name|mac> Specify adapter to use by his Name or MAC address (if this option does not defined - default adapter used) -c, --connect <name|mac> Connect all supported audio profiles on the device -d, --disconnect <name|mac> Disconnect all audio profiles on the device AUTHOR
Alexander Orlenko <zxteam@gmail.com>. SEE ALSO
bt-adapter(1) bt-agent(1) bt-device(1) bt-input(1) bt-monitor(1) bt-network(1) bt-serial(1) 2010-08-11 bt-audio(1)
All times are GMT -4. The time now is 08:31 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy