hacmp network adapter re-define Post: 302073630

10 More Discussions You Might Find Interesting

1. Solaris

Sun v440/v880 network adapter teaming

Is it possible to team two network adapters for fault tolerance in a Sun v440 or v880 Solaris 8 box? If so how would I go about doing so?

2. IP Networking

define IP protocols on network

what method would I use to determine which IP protocols network

3. AIX

change network adapter

hello i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 ) what i need to do after the new adapter installed on the machine? thanks best regards ariec

4. AIX

How to active this network adapter?

When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command: entstat -all ent#|grep -i priority Priority: 5 Active: False How to make Active to True?

5. UNIX for Dummies Questions & Answers

External Network Adapter for Solaris 10

Hi All, I am new here - this is my first post. I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the...

6. AIX

HACMP: set preferred adapter for service ip

Hi, lets say we have two boot interfaces en0 en1 and two resource groups, with two service ips, sip1 and sip2, one persistent ip pers1 both persistend and service ips are applied as ip-alias when I start the cluster, and bring the resource groups up, it looks like en0: sip1 and sip2 ...

7. UNIX for Dummies Questions & Answers

SCO Unixware 7.1.4 Network Adapter Error

Hi All I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached. I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network...

8. UNIX for Dummies Questions & Answers

Simulated driver for Network Interface Adapter

Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean? - It has to run on all network adapters - It has to be as simple as it can be - It has to run on all linux distributions (or at least most of them) - It does not have to run a network...

9. Hardware

Problematic RTL8188EE Wireless Network Adapter

Good Day All, There are numerous results when searching google on this issue, however, none seem to have a solution. I have read until my eyes bleed and banged my head on the table more than once! :) I am hoping to resolve this issue -- or at least have a decent workaround. It is a real...

10. SCO

Can not recognize network adapter SCO UNIX in HP z400

hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback. show message : dlpid:unable to open network adapter driver...

LEARN ABOUT OSF1

vb

vb(7)							 Miscellaneous Information Manual						     vb(7)

NAME

       vb, sys_attrs_vme_vba - VMEbus backplane Ethernet interface

SYNOPSIS

       controller vb0 at vba0

DESCRIPTION

       The  VMEbus  backplane (vb) interface provides access to an Ethernet network through the VMEbus backplane driver, which acts as an Ethernet
       Datalink Layer driver.  This interface allows VMEbus-based systems to communicate directly over the VMEbus to other VMEbus-based systems on
       the same backplane, or on other Ethernet connected systems outside the backplane through a gateway node on the backplane.

       Both  the  Tru64  UNIX  and VxWorks for Alpha (Version 3.1 or higher) software support the vb driver as well as communication between these
       systems on the same backplane.  The Tru64 UNIX vb driver is supported on AXPvme and Alpha VME SBCs and Alpha VME 2100 systems.

       The VMEbus backplane interface requires you to modify the /etc/sysconfigtab file on your AXPvme or Alpha VME system in order  to  configure
       the  vb driver and to map VMEbus windows for the system.  Mapping the VMEbus windows on one node requires knowledge about every node in the
       vb network.

									  Note

       Do not modify any vme_vba kernel subsystem attributes.  To configure a vb network node, you modify attributes of the vb	driver	(vb:)  and
       the system's VMEbus adapter (vba_vipvic: or vba_univ:).

       See System Configuration Supplement: OEM Platforms for detailed information about the use of the vb interface on Alpha VME systems, includ-
       ing the following topics: VMEbus backplane (vb) network overview Configuring vb network nodes  Modifying  vb  driver  attributes  Modifying
       vba_vipvic adapter attributes Modifying vba_univ adapter attributes Examples Related ioctl commands Diagnostic messages Errors

RELATED INFORMATION

       Interfaces:  sys_attrs_vba_vipvic(7), sys_attrs_vba_univ(7), sysconfigdb(8)

       Network Administration, System Configuration Supplement: OEM Platforms delim off

																	     vb(7)

10 More Discussions You Might Find Interesting

1. Solaris

Sun v440/v880 network adapter teaming

Discussion started by: ghuber

2. IP Networking

define IP protocols on network

Discussion started by: mar mar

3. AIX

change network adapter

Discussion started by: ariec

4. AIX

How to active this network adapter?

Discussion started by: rainbow_bean

5. UNIX for Dummies Questions & Answers

External Network Adapter for Solaris 10

Discussion started by: soulmerchant

6. AIX

HACMP: set preferred adapter for service ip

Discussion started by: funksen

7. UNIX for Dummies Questions & Answers

SCO Unixware 7.1.4 Network Adapter Error

Discussion started by: flashinwrx