04-24-2006
tape drive
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but I do not know which type of backup files in my tape (cpio or tar) also I do not know device name like /dev/rStp0 or xStp0
how can I find it ?
thanks
Alice..
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm trying to install a tape drive on a compaq SCO OS 505. well I have gone through the mkdev tape comands and what have you yet no luck. when I reboot and do a simple tape rewind it gives me an error no such device etc.etc. IS there a diference in the xct0 and rct0 a the default?
help.. (2 Replies)
Discussion started by: kikkin
2 Replies
2. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
3. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
4. SCO
Dear All,
I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as... (4 Replies)
Discussion started by: njoroge
4 Replies
5. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
6. SCO
I've recently been tasked with "refurbishing" an HP Proliant ML370 running SCO 5.0...something. This is primarily used for legacy support and is kept on a shelf for safe keeping. The scope of work includes hardware diagnostics and blowing the dust out.
I have run HP diagnostics on the array,... (1 Reply)
Discussion started by: v1corp
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
8. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
TS(4) Kernel Interfaces Manual TS(4)
NAME
ts - TS-11 magtape interface
SYNOPSIS
/sys/conf/SYSTEM:
NTS ts_drives # TS11
/etc/dtab:
#Name Unit# Addr Vector Br Handler(s) # Comments
ts ? 172520 224 5 tsintr # ts11 driver
major device number(s):
raw: 8
block: 2
minor device encoding:
bits 0003 specify TS drive
bit 0004 specifies no-rewind operation
bit 0010 ignored
DESCRIPTION
The ts-11 combination provides a standard tape drive interface as described in mtio(4). The ts-11 operates only at 1600 bpi, and only one
transport is possible per controller.
FILES
/dev/MAKEDEV script to create special files
/dev/MAKEDEV.local script to localize special files
SEE ALSO
mt(1), tar(1), tp(1), mtio(4), ht(4), tm(4), dtab(5), autoconfig(8)
DIAGNOSTICS
ts%d: no write ring. An attempt was made to write on the tape drive when no write ring was present; this message is written on the termi-
nal of the user who tried to access the tape.
ts%d: not online. An attempt was made to access the tape while it was offline; this message is written on the terminal of the user who
tried to access the tape.
ts%d: hard error bn%d xs0=%b xs1=%b xs2=%b xs3=%b. A hard error occurred on the tape at block bn; status registers 0-3 are printed in
octal and symbolically decoded as bits.
ts%d: addr mod 4 != 0. The address of a TS-11 command packet was not on an even longword boundary.
BUGS
If any non-data error is encountered on non-raw tape, it refuses to do anything more until closed.
The device lives at the same address as a tm-11 tm(4).
3rd Berkeley Distribution January 28, 1988 TS(4)