08-14-2002
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello,
I need to modify the semaphores parameters on a Linux server Debian 2.2.R3. How can I do it?
Thks. (6 Replies)
Discussion started by: annececile
6 Replies
2. UNIX for Dummies Questions & Answers
Hi friends,
i would like to know the kernal information (semaphores), which command do i use
Thanks (4 Replies)
Discussion started by: shaan_dmp
4 Replies
3. UNIX for Dummies Questions & Answers
Hi,
Does anyone know if it is possible to know the current value of a kernel module parameters after the module is loaded. Are the values of the parameters advertised at some /proc or /sys location ?
The only thing I know is modinfo, that actually looks a the module .ko and gives a... (3 Replies)
Discussion started by: macL
3 Replies
4. UNIX for Advanced & Expert Users
I am running Putty 0.60 from Windows XP and I am connecting to a Linux box.
I would like to be able to pass a command line parameter to my Linux session so that my Linux session can execute a specific command, depending on the command line parameter. I have looked on the Internet and tried... (1 Reply)
Discussion started by: SFNYC
1 Replies
5. AIX
Hello,
How can I setup the ulimit for memory permanent
ulimit -m unlimited
ulimit -a Output from the ulimit command should be similar to the following:time(seconds) unlimited
file(blocks) unlimited
data(kbytes) 2097152
stack(kbytes) 32768... (4 Replies)
Discussion started by: filosophizer
4 Replies
6. Solaris
Hi,
Can you please let me know about kernal parameters?
Where we can see that kernal parameters?
we are using System = SunOS 5.10.
Please let me know commands to see these kernal parameters file or files. (1 Reply)
Discussion started by: kancherla.sree
1 Replies
7. Emergency UNIX and Linux Support
Hi,
I need to set qlogic qla2xxx parameters in /etc/modprobe.conf
(Oracle Linux Server release 5.7, almost equal to RedHat 5.7)
two questions:
how can I pass this parameters to the module while it is loaded (fibre channel luns are in use), if possible at all
and how can I check the... (3 Replies)
Discussion started by: funksen
3 Replies
8. Red Hat
please tell me the list of kernel parameters in RHEL 5.7
Because we've a requirement in one project.
Also tell me the importance of eah kernel parameter if possible.
==Thanks in Advance==:):D (1 Reply)
Discussion started by: vamshigvk475
1 Replies
9. Linux
Please clarify on below two which one is the latest Kernal version.
Also clarify me , how to break and understand, which part meant for what?
kernel-2.6.18-348.6.1.el5.i686.rpm
kernel-2.6.18-308.11.1.el5.i686.rpm
Thanks (3 Replies)
Discussion started by: Siva SQL
3 Replies
10. Shell Programming and Scripting
Hello.
It's my first steps in creat bash skript.
This is my skript :
mysql -e "
UPDATE datebase.table
SET U_O_ID=NULL
WHERE U_O_ID LIKE '"$w4"'
AND N_U != '"$w1"'
" -u admin -p""Password"" ;
It doesn't work.
I find a lot of topic about it, but I didn't find simple answer.... (7 Replies)
Discussion started by: karp
7 Replies
LEARN ABOUT NETBSD
urlphy
URL(4) BSD Kernel Interfaces Manual URL(4)
NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8)
HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
September 18, 2006 BSD