07-09-2002
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi everyone
I am having some real difficulties getting a dial in modem to work on one of my HP boxes. It's a mux modem on port 7 which I have set up at 9600 baud.
I can dial in, the handshakes are completed, but then it returns incoherent characters on the emulation screen. I think my dial in... (1 Reply)
Discussion started by: alwayslearningunix
1 Replies
2. UNIX for Advanced & Expert Users
I've spent enough time trying to put on work Lucent Winmodem in my armada M300 (compaq laptop) I use Mandrake 8.0 but as soon as i get connected
and prompmts appears modem shutsdown.
Does any one had a similar situation, solved it?
cheers (2 Replies)
Discussion started by: alex blanco
2 Replies
3. UNIX for Dummies Questions & Answers
Hi!
I have a little prob with dialing up to the internet... When I try connect, it says "Sorry, modem is busy"...
Specs:
Laptop
56K modem
Slackware 8.0
Kernel 2.4.5
Cheers;) (4 Replies)
Discussion started by: satan404
4 Replies
4. UNIX for Dummies Questions & Answers
Specs:
Dlink DFE-560EL external modem.
RedHat 7.1
How do you turn off the modem volume? I am getting annoyed of it beeping everytime I use it but there is no switch on the hardware to tune down the volume.
I have tried using minicom and use the following commands:
ATL0
ATM0
Next, I... (2 Replies)
Discussion started by: arz
2 Replies
5. UNIX for Dummies Questions & Answers
I have got Suse 8.0 by using a modem (US Robotics 56K Faxmodem Ext).
During connection i got the error 16. I tried it under RedHat and Mandrake too.....same problem. What can i do ?
Thanx...a lot...
Logfile:
SuSE Meta pppd (smpppd), Version 0.73 on zuhause.
wwwoffle not is running ... (1 Reply)
Discussion started by: Pennywize
1 Replies
6. UNIX for Dummies Questions & Answers
Ok. I tried following the directions from some of the other threads, but I've hit a road block.
I have red hat 7.3 and I installed the hcf package:
hcfpcimodem-0.99lnxtbeta03042700k2.4.18_3-1rh.i386.rpm
It installed ok, no errors, but I still can't get linux to find my modem. I've tried... (2 Replies)
Discussion started by: lawadm1
2 Replies
7. UNIX for Dummies Questions & Answers
Im using Kinternet with a Lucent modem on Suse 9.0
Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0
This is the log that Kinternet gives after trying to connect:
SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux.
Status... (0 Replies)
Discussion started by: Synbios
0 Replies
8. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
9. Solaris
hi folks,
i am looking for a analog modem to use it with a solaris9 sparc mashine. as far as i know, solaris communicates with the modem using AT-commands. so do i need a special modem for solaris or just a modem? i am open for everything. PCI-modem, seriell modem, usb modem. what are you using? i... (1 Reply)
Discussion started by: pressy
1 Replies
10. IP Networking
How to get information that where is my modem configured in /dev.
I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Discussion started by: s123.radha
0 Replies
LEARN ABOUT DEBIAN
device::modem::usrobotics
Device::Modem::UsRobotics(3pm) User Contributed Perl Documentation Device::Modem::UsRobotics(3pm)
NAME
Device::Modem::UsRobotics - USR modems extensions to control self-mode
SYNOPSIS
use Device::Modem::UsRobotics;
my $modem = new Device::Modem::UsRobotics( port => '/dev/ttyS1' );
$modem->connect( baudrate => 9600 );
my %info = $modem->messages_info();
print "There are $info{unreleased_voice_msg} unread voice messages on $info{stored_voice_msg} total
";
print "There are $info{unreleased_fax_msg} unread fax messages on $info{stored_fax_msg} total
";
# Get details about message n. X
my %msg = $modem->message_info(1);
index type information attributes status day hour minute
callerid page addresshigh addresslow checksum
print 'This is a ', ($msg{type} == 2 ? 'voice' : 'fax'), 'message', "
";
print 'It came from no. ', $msg{callerid}, "
";
# ...
# Now clear all messages
$modem->clear_memory();
WARNING
This module is not documented yet, and it is a rough work in progress. Until now, it correctly reads voice/fax messages information, but
when saving voice messages to disk, sometimes they are incorrectly decoded.
So, if you need a working program, check out the good old TkUsr by Ludovic Drolez, unless you want to help develop
Device::Modem::UsRobotics.
DOCS TO BE COMPLETED FROM NOW.....
Yes, I'm a bad boy :-)
DESCRIPTION
Bla Bla Bla...
METHODS
clear_memory()
Used to permanently clear the memory space of the modem. There are separate memory spaces, one for voice/fax messages and one for user set-
tings. Examples:
$modem->clear_memory('user'); # or $modem->clear_memory(1)
$modem->clear_memory('messages'); # or $modem->clear_memory(2)
To clear both, you can use:
$modem->clear_memory('all'); # or $modem->clear_memory(0);
Parameters:
$memtype
String or integer that selects the type of memory to be cleared, where 0 is for "all", 1 is for "user" memory, 2 is for "messages" mem-
ory.
SUPPORT
Please feel free to contact me at my e-mail address cosimo@cpan.org for any information, to resolve problems you can encounter with this
module or for any kind of commercial support you may need.
AUTHOR
Cosimo Streppone, cosimo@cpan.org
COPYRIGHT
(C) 2004-2005 Cosimo Streppone, cosimo@cpan.org
This library is free software; you can only redistribute it and/or modify it under the same terms as Perl itself.
SEE ALSO
Device::Modem, perl
perl v5.8.8 2005-04-30 Device::Modem::UsRobotics(3pm)