07-09-2002
Modem
Pleaseee... Helpppp.... !!!
I am using SCO Open Server 5.05. Recently, i have upgraded the system which means transfer all apps and data to the new system. Everything work well except one thing. On my old system i have an external modem which to dial out. Now that i use the same modem on the new system which doesn't seems to work..... Everytime i tried to dial out.... All i got is " CAN NOT OPEN MODEM ". What could be the problem ? And how should I correct this problem... Pleaseee Helpppp....
Thank you so much for you time
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi everyone
I am having some real difficulties getting a dial in modem to work on one of my HP boxes. It's a mux modem on port 7 which I have set up at 9600 baud.
I can dial in, the handshakes are completed, but then it returns incoherent characters on the emulation screen. I think my dial in... (1 Reply)
Discussion started by: alwayslearningunix
1 Replies
2. UNIX for Advanced & Expert Users
I've spent enough time trying to put on work Lucent Winmodem in my armada M300 (compaq laptop) I use Mandrake 8.0 but as soon as i get connected
and prompmts appears modem shutsdown.
Does any one had a similar situation, solved it?
cheers (2 Replies)
Discussion started by: alex blanco
2 Replies
3. UNIX for Dummies Questions & Answers
Hi!
I have a little prob with dialing up to the internet... When I try connect, it says "Sorry, modem is busy"...
Specs:
Laptop
56K modem
Slackware 8.0
Kernel 2.4.5
Cheers;) (4 Replies)
Discussion started by: satan404
4 Replies
4. UNIX for Dummies Questions & Answers
Specs:
Dlink DFE-560EL external modem.
RedHat 7.1
How do you turn off the modem volume? I am getting annoyed of it beeping everytime I use it but there is no switch on the hardware to tune down the volume.
I have tried using minicom and use the following commands:
ATL0
ATM0
Next, I... (2 Replies)
Discussion started by: arz
2 Replies
5. UNIX for Dummies Questions & Answers
I have got Suse 8.0 by using a modem (US Robotics 56K Faxmodem Ext).
During connection i got the error 16. I tried it under RedHat and Mandrake too.....same problem. What can i do ?
Thanx...a lot...
Logfile:
SuSE Meta pppd (smpppd), Version 0.73 on zuhause.
wwwoffle not is running ... (1 Reply)
Discussion started by: Pennywize
1 Replies
6. UNIX for Dummies Questions & Answers
Ok. I tried following the directions from some of the other threads, but I've hit a road block.
I have red hat 7.3 and I installed the hcf package:
hcfpcimodem-0.99lnxtbeta03042700k2.4.18_3-1rh.i386.rpm
It installed ok, no errors, but I still can't get linux to find my modem. I've tried... (2 Replies)
Discussion started by: lawadm1
2 Replies
7. UNIX for Dummies Questions & Answers
Im using Kinternet with a Lucent modem on Suse 9.0
Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0
This is the log that Kinternet gives after trying to connect:
SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux.
Status... (0 Replies)
Discussion started by: Synbios
0 Replies
8. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
9. Solaris
hi folks,
i am looking for a analog modem to use it with a solaris9 sparc mashine. as far as i know, solaris communicates with the modem using AT-commands. so do i need a special modem for solaris or just a modem? i am open for everything. PCI-modem, seriell modem, usb modem. what are you using? i... (1 Reply)
Discussion started by: pressy
1 Replies
10. IP Networking
How to get information that where is my modem configured in /dev.
I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Discussion started by: s123.radha
0 Replies
LEARN ABOUT REDHAT
wvdialconf
WVDIALCONF(1) General Commands Manual WVDIALCONF(1)
NAME
wvdialconf - build a configuration file for wvdial(1)
SYNOPSIS
wvdialconf /etc/wvdial.conf
DESCRIPTION
wvdialconf detects your modem, its maximum baud rate, and a good initialization string and generates or updates the wvdial(1) configuration
file based on this information.
wvdialconf is completely non-interactive. You still need to edit /etc/wvdial.conf to specify the phone number, login name, and password of
your internet account in order for wvdial(1) to work.
It is safe to run wvdialconf if a configuration file already exists. In that case, only the Modem, Baud, Init, and Init2 options are
changed in the [Dialer Defaults] section, and only if autodetection is successful.
BUGS
We're willing to entertain the possibility. Let us know if you have any problems by sending an e-mail to <wvdial@nit.ca>.
Also, there is now a mailing list for discussion about wvdial. If you are having problems, or have anything else to say, send e-mail to
<wvdial-list@lists.nit.ca>.
DIAGNOSTICS
An exit status of 0 means that a modem was detected and the configuration file was updated successfully.
Any other value means that something went wrong and the configuration file was unchanged.
AUTHORS
Dave Coombs and Avery Pennarun for Net Integration Technologies, as part of the Worldvisions Weaver project.
SEE ALSO
wvdial(1), wvdial.conf(5).
Worldvisions August 1998 WVDIALCONF(1)