Sponsored Content
Full Discussion: QMail
Top Forums UNIX for Dummies Questions & Answers QMail Post 2059 by mib on Tuesday 17th of April 2001 02:17:20 AM
Old 04-17-2001
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

QMail Help

My company is running qmail on our Unix server. I would like to run a MySQL script whenever an email was sent to a specific email address. I don't want to have to check every email that comes in, so I was thinking that the script would run when the message arrives at the specific mailbox. Is there... (0 Replies)
Discussion started by: perryl7
0 Replies

2. UNIX for Dummies Questions & Answers

Qmail Configuration

hey, plz tell me someone how to configure qmail in redhat linux 9.0. (1 Reply)
Discussion started by: raj_shivage
1 Replies

3. Solaris

Qmail on Solaris 9

I want to configure Qmail on my server (v240/SPARC 1GHz/1GB RAM /2x36GB HDD). Anybody help me where to download, and how to configure Qmail on Sol9. Thanks in advanced, Tinh (1 Reply)
Discussion started by: tinhlx
1 Replies

4. Solaris

Qmail - possible?

Hi guys, Could you please advice me as im a new guy into Solaris ...is it possible to have qmail up and running on Solaris 10 and do you know where i can find some documentation on downloading and configuring - qmail? thank you guys vladi, (2 Replies)
Discussion started by: saveka
2 Replies

5. Gentoo

Gentoo and Qmail

Hello all, I want to create a qmail to just forward messages to a valid smtp over the internet, so I can use mutt to send messages as well as recieving them. Is there an easy way of doing this? My SMTP server requires authentication. Thanks a lot. (2 Replies)
Discussion started by: Zarnick
2 Replies

6. UNIX and Linux Applications

Qmail and duplicate

hello, I have a qmail server on Freebsd that is sending periodic duplicate emails. I dug around and found out that when connecting to the server through a telnet session everything goes good until i send the DATA command, type a message and enter the "." it takes like 5 minutes to get the 250 ok... (4 Replies)
Discussion started by: mike171562
4 Replies

7. SuSE

qmail question - about addressbook(All)

I have installed qmail on SuSe linux box with mysql.Qmail is running fine and has no problem.Now I want to develop sonme new features by integrating our ERP with qmail.For that I have to enter more information about employee in Qmail Addressbook.I am attaching screenshot which is describing present... (0 Replies)
Discussion started by: thetakan
0 Replies

8. UNIX and Linux Applications

QMail spam

we had an emergency situation and had to rebuild a qmail server last night. Email now that is designated as spam gets stuck in a loop and we get a ndr. I would like for email not destined for a valid account or classified as spam be deleted rather then forwarded on to our exchange server. ... (1 Reply)
Discussion started by: egrotjahn
1 Replies

9. UNIX for Dummies Questions & Answers

qmail bounce

Hello, i seem to be facing a strange problem. I send my emails via qmail (on linux) and all the emails gets delivered to the recipient's inbox and bounces back to the sender's address and well. This happens irrespective of the recipient's email domain (gmail, yahoo, hotmail...). We recently... (0 Replies)
Discussion started by: pradeeptg
0 Replies

10. Red Hat

Qmail

hi all, i want to install Qmail but i don't from where can i get the package , and also if one know source that can explain qmail kindly tell me about it (3 Replies)
Discussion started by: linux_land
3 Replies
URL(4)							   BSD Kernel Interfaces Manual 						    URL(4)

NAME
url -- Realtek RTL8150L USB Ethernet driver SYNOPSIS
url* at uhub? urlphy* at mii? DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip. The url driver supports the following adapters: CompUSA USBKR100 GreenHouse GH-USB100B Melco Inc. LUA-KTX Sitecom LN013 For more information on configuring this device, see ifconfig(8). DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8) HISTORY
The url device driver first appeared in NetBSD 1.6. AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>. BSD
September 18, 2006 BSD
All times are GMT -4. The time now is 08:24 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy