04-24-2002
Ethernet Again
We have no file like \etc\rc.config.d\netconf in our Linux then what should we have to do.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies
2. Cybersecurity
I suspect that someone is using a sniffer on my Ethernet connection,
OS X 10.3.9, DSL,
ok, I'm in terminal using the "ifconfig" command >
flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384
right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
Discussion started by: su"do"er
1 Replies
3. UNIX for Advanced & Expert Users
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies
4. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
5. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
6. AIX
Hello everyone
I have a problem with one server, has Aix 5.3 in the errpt has this message
IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION
F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE
EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN
F3931284 ... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies
7. Solaris
my solris box network is unreachable how to solve this
ipaddress assiagning and entry in vi /etc/host
how to solve network is unreachable (2 Replies)
Discussion started by: tirupathi
2 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
LEARN ABOUT NETBSD
npm-config
NPM-CONFIG(1) NPM-CONFIG(1)
NAME
npm-config - Manage the npm configuration files
SYNOPSIS
npm config set <key> <value> [-g|--global]
npm config get <key>
npm config delete <key>
npm config list [-l] [--json]
npm config edit
npm get <key>
npm set <key> <value> [-g|--global]
aliases: c
DESCRIPTION
npm gets its config settings from the command line, environment variables, npmrc files, and in some cases, the package.json file.
See npm help 5 npmrc for more information about the npmrc files.
See npm help 7 npm-config for a more thorough discussion of the mechanisms involved.
The npm config command can be used to update and edit the contents of the user and global npmrc files.
Sub-commands
Config supports the following sub-commands:
set
npm config set key value
Sets the config key to the value.
If value is omitted, then it sets it to "true".
get
npm config get key
Echo the config value to stdout.
list
npm config list
Show all the config settings. Use -l to also show defaults. Use --json to show the settings in json format.
delete
npm config delete key
Deletes the key from all configuration files.
edit
npm config edit
Opens the config file in an editor. Use the --global flag to edit the global config.
SEE ALSO
o npm help 5 folders
o npm help 7 config
o npm help 5 package.json
o npm help 5 npmrc
o npm help npm
January 2019 NPM-CONFIG(1)