02-01-2002
How to install modem in SCO OPEN SERVER VER 5.05
Hello Friends.
I would like to know couple of questions.
1. How to install internal modem in unix operating system.
I have a toshiba laptop with toshiba v.90 internal modem .
2. Where is hyper Terminal in Unix.
3. Where i can get the support for windows like we used to have vipex.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm new to the whole Unix thing and have inherited a network running Macs, Windows 2000 and Unix. The Unix side is very suspect at this point and I want to change out the server.
I'd love to use one of the new Apple servers but can't find any info on what "flavors" of Unix it will run. Specificly... (3 Replies)
Discussion started by: matthewd
3 Replies
2. UNIX for Advanced & Expert Users
I'm in the process of installing SCO Open Server 5.05 on the following platform:
Hardware:
IBM 300PL
64 MB RAM
Yamaha 16/4/16 CDRW (Internal defined on SCSI ID 3 LUN 0)
I'm able to boot from the CD and advance to the Installation screen but when it asks for where the media source will... (3 Replies)
Discussion started by: budrito
3 Replies
3. Filesystems, Disks and Memory
Help, if possible.
In SCO Open Server with installation of two-channel RAID controller the following happens: on the channel 0 disk array is seen by an operational system, and on the channel 1 array is not seen (simultaneously). That is the operational system can not simultaneously use more than... (1 Reply)
Discussion started by: pko60
1 Replies
4. SCO
Dear All,
I am considering installing SCO Open Server as an alternative to MS Exchange. Has anybody had any real world experience of using Open Office?
Thanks,
TC. (1 Reply)
Discussion started by: TCuk
1 Replies
5. SCO
How can I to know procesor type. (1 Reply)
Discussion started by: Batya
1 Replies
6. SCO
I have to purchase SCO Open Server 6.0, so I want to know from where I can get SCO Open Server 6.0 and what is the min. cost in which I can avail this.
Thanks and Regards
Himanshu
Software Engineer
R&D Department (4 Replies)
Discussion started by: ghimanshu
4 Replies
7. SCO
Hi,
Completely new to UNIX - so be gentle
Cut a long story short, we have a micros 8700 system (eclipse) that needs the Micros 8700 software installed.
The system needs UNIX and I have downloaded and successfully installed SCO open Server 6 and can log into root e.t.c.
Now I have... (13 Replies)
Discussion started by: kennyruss
13 Replies
8. SCO
Dear All,
Newbie here, hope my post goes to the correct room.
System: SCO Open Server 6.0
Everything running well, after this Sunday morning noone can login via telnet or via putty, the system suddenly reject without any message (and also ftp). The local IT Support there (without enough... (2 Replies)
Discussion started by: virgani
2 Replies
9. UNIX for Advanced & Expert Users
Hi my name is Danilo.
I'm trying to install Sco foxbase + 2.1.2d. When i tried to install it with "custom" command, i receive the error:
"sed: cannot open: ./tmp/perms/prep/*/prep.message: No such file or directory (error 2)
The Operative System is Sco Open Server 5.0.7v (the virtualized version... (1 Reply)
Discussion started by: danilosevilla
1 Replies
10. SCO
Hi my name is Danilo.
I'm trying to install Sco foxbase + 2.1.2d. When i tried to install it with "custom" command, i receive the error:
"sed: cannot open: ./tmp/perms/prep/*/prep.message: No such file or directory (error 2)
The Operative System is Sco Open Server 5.0.7v (the virtualized version... (1 Reply)
Discussion started by: danilosevilla
1 Replies
LEARN ABOUT FREEBSD
acpi_toshiba
ACPI_TOSHIBA(4) BSD Kernel Interfaces Manual ACPI_TOSHIBA(4)
NAME
acpi_toshiba -- Toshiba HCI interface
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device acpi_toshiba
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
acpi_toshiba_load="YES"
DESCRIPTION
HCI is Toshiba's Hardware Control Interface which is somewhat uniform across their models. The acpi_toshiba driver allows the user to manip-
ulate HCI-controlled hardware using a number of sysctl(8) variables.
SYSCTL VARIABLES
The following sysctls are currently implemented:
hw.acpi.toshiba.force_fan
Causes active cooling to be forcibly enabled ('1') or disabled ('0') regardless of the current temperature.
hw.acpi.toshiba.video_output
Sets the active display to use according to a bitwise OR of the following:
0 No display
1 LCD
2 CRT
4 TV-Out
Only some systems (i.e., the Libretto L5) support video switching via this hardware-specific driver. Use the acpi_video(4) driver
for generic video output support.
hw.acpi.toshiba.lcd_brightness
Makes the LCD backlight brighter or dimmer (higher values are brighter).
hw.acpi.toshiba.lcd_backlight
Turns the LCD backlight on and off.
hw.acpi.toshiba.cpu_speed
Sets the CPU speed to the specified speed. This provides functionality similar to the hw.acpi.cpu.throttle_state variable. Higher
sysctl values mean lower CPU speeds.
Defaults for these variables can be set in sysctl.conf(5), which is parsed at boot-time.
LOADER TUNABLES
The hw.acpi.toshiba.enable_fn_keys tunable enables or disables the function keys on the keyboard. Function keys are enabled by default.
This behaviour can be changed at the loader(8) prompt or in loader.conf(5).
SEE ALSO
acpi(4), acpi_video(4), loader.conf(5), sysctl.conf(5), sysctl(8)
HISTORY
The acpi_toshiba driver first appeared in FreeBSD 5.1.
AUTHORS
The acpi_toshiba driver was written by Hiroyuki Aizu <aizu@navi.org>. This manual page was written by Philip Paeps <philip@FreeBSD.org>.
BSD
February 8, 2010 BSD