SOCKET(2)						      BSD System Calls Manual							 SOCKET(2)

NAME

     socket -- create an endpoint for communication

SYNOPSIS

     #include <sys/types.h>
     #include <sys/socket.h>

     int
     socket(int domain, int type, int protocol);

DESCRIPTION

     Socket() creates an endpoint for communication and returns a descriptor.

     The domain parameter specifies a communications domain within which communication will take place; this selects the protocol family which
     should be used.  These families are defined in the include file <sys/socket.h>.  The currently understood formats are

	   AF_UNIX	   (UNIX internal protocols),
	   AF_INET	   (ARPA Internet protocols),
	   AF_ISO	   (ISO protocols),
	   AF_NS	   (Xerox Network Systems protocols), and
	   AF_IMPLINK	   (IMP host at IMP link layer).

     The socket has the indicated type, which specifies the semantics of communication.  Currently defined types are:

	   SOCK_STREAM
	   SOCK_DGRAM
	   SOCK_RAW
	   SOCK_SEQPACKET
	   SOCK_RDM

     A SOCK_STREAM type provides sequenced, reliable, two-way connection based byte streams.  An out-of-band data transmission mechanism may be
     supported.  A SOCK_DGRAM socket supports datagrams (connectionless, unreliable messages of a fixed (typically small) maximum length).  A
     SOCK_SEQPACKET socket may provide a sequenced, reliable, two-way connection-based data transmission path for datagrams of fixed maximum
     length; a consumer may be required to read an entire packet with each read system call.  This facility is protocol specific, and presently
     implemented only for PF_NS.  SOCK_RAW sockets provide access to internal network protocols and interfaces.  The types SOCK_RAW, which is
     available only to the super-user, and SOCK_RDM, which is planned, but not yet implemented, are not described here.

     The protocol specifies a particular protocol to be used with the socket.  Normally only a single protocol exists to support a particular
     socket type within a given protocol family.  However, it is possible that many protocols may exist, in which case a particular protocol must
     be specified in this manner.  The protocol number to use is particular to the communication domain in which communication is to take place;
     see protocols(5).

     Sockets of type SOCK_STREAM are full-duplex byte streams, similar to pipes.  A stream socket must be in a connected state before any data may
     be sent or received on it.  A connection to another socket is created with a connect(2) call.  Once connected, data may be transferred using
     read(2) and write(2) calls or some variant of the send(2) and recv(2) calls.  When a session has been completed a close(2) may be performed.
     Out-of-band data may also be transmitted as described in send(2) and received as described in recv(2).

     The communications protocols used to implement a SOCK_STREAM insure that data is not lost or duplicated.  If a piece of data for which the
     peer protocol has buffer space cannot be successfully transmitted within a reasonable length of time, then the connection is considered bro-
     ken and calls will indicate an error with -1 returns and with ETIMEDOUT as the specific code in the global variable errno.  The protocols
     optionally keep sockets ``warm'' by forcing transmissions roughly every minute in the absence of other activity.  An error is then indicated
     if no response can be elicited on an otherwise idle connection for a extended period (e.g. 5 minutes).  A SIGPIPE signal is raised if a
     process sends on a broken stream; this causes naive processes, which do not handle the signal, to exit.

     SOCK_SEQPACKET sockets employ the same system calls as SOCK_STREAM sockets.  The only difference is that read(2) calls will return only the
     amount of data requested, and any remaining in the arriving packet will be discarded.

     SOCK_DGRAM and SOCK_RAW sockets allow sending of datagrams to correspondents named in send(2) calls.  Datagrams are generally received with
     recvfrom(2), which returns the next datagram with its return address.

     An fcntl(2) call can be used to specify a process group to receive a SIGURG signal when the out-of-band data arrives.  It may also enable
     non-blocking I/O and asynchronous notification of I/O events via SIGIO.

     The operation of sockets is controlled by socket level options.  These options are defined in the file <sys/socket.h>.  Setsockopt(2) and
     getsockopt(2) are used to set and get options, respectively.

RETURN VALUES

     A -1 is returned if an error occurs, otherwise the return value is a descriptor referencing the socket.

ERRORS

     The socket() call fails if:

     [EPROTONOSUPPORT]	The protocol type or the specified protocol is not supported within this domain.

     [EMFILE]		The per-process descriptor table is full.

     [ENFILE]		The system file table is full.

     [EACCES]		Permission to create a socket of the specified type and/or protocol is denied.

     [ENOBUFS]		Insufficient buffer space is available.  The socket cannot be created until sufficient resources are freed.

SEE ALSO

     accept(2), bind(2), connect(2), getprotoent(3), getsockname(2), getsockopt(2), ioctl(2), listen(2), read(2), recv(2), select(2), send(2),
     shutdown(2), socketpair(2), write(2)

     An Introductory 4.3 BSD Interprocess Communication Tutorial, reprinted in UNIX Programmer's Supplementary Documents Volume 1.

     BSD Interprocess Communication Tutorial, reprinted in UNIX Programmer's Supplementary Documents Volume 1.

HISTORY

     The socket() function call appeared in 4.2BSD.

4.2 Berkeley Distribution					   June 4, 1993 					 4.2 Berkeley Distribution