Sponsored Content
Full Discussion: JumpStart
Top Forums UNIX for Dummies Questions & Answers JumpStart Post 11084 by doeboy on Wednesday 28th of November 2001 06:27:39 PM
Old 11-28-2001
You can try searching for Solaris Jumpstart FAQ.

http://www.sunhelp.org/ has some helpful docs too I think.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Jumpstart?

I have been asked to research Jumpstart and don't know where to begin! Any ideas would be much appreciated! Thanks! :-) (1 Reply)
Discussion started by: avana100
1 Replies

2. UNIX for Advanced & Expert Users

JUmpstart on a pc

HI. i was wondering if you can jumpstart using the solaris intel platform? please help thanks (3 Replies)
Discussion started by: souldier
3 Replies

3. UNIX for Advanced & Expert Users

Jumpstart

Hi, where can i find documention on how to create a jumpstart system? dori (2 Replies)
Discussion started by: dorilevy
2 Replies

4. Solaris

help with jumpstart

Hello all, I configured a jumpstart server ( the server is in the same subnet as the client) and gave boot net - install in the client. The client boots up shows the banner and then displays error: cant read disk label cant open disk label package and then goes to OK prompt. What... (1 Reply)
Discussion started by: Pratik Gharti
1 Replies

5. Solaris

Jumpstart Help

Hi Peeps, Created a jumpstart server for an unattened install and it works, but got 2 bugs in the config which I would like to work out: when you boot net install It still asks you to select a language and locale, after you do this it kicks of an unattended install. So my question is,... (5 Replies)
Discussion started by: callmebob
5 Replies

6. Solaris

Jumpstart solaris

Hi all , I am trying to jumpstart ( webstart) solaris 9 on E2900 ( client) using the DVD of a V440 server ( jumstart server). I did the setup for the V440 as follows : cleaning up preexisting install client "XXXXXXX" removing XXXXXXXfrom bootparams removing /etc/bootparams, since it is... (14 Replies)
Discussion started by: ppass
14 Replies

7. Solaris

Jumpstart issues, help please.

1.I wish to perform a Jumpstart installation, the client being Ultra 5 Sparc and jumpstart Server being ultra 20 AMD system. 2.I think i have done all the procedures right, like putting the mac address of Sparc 1 to /etc/ethers, creating sysidcfg file, and profile file: 3.When I issued the boot... (7 Replies)
Discussion started by: saagar
7 Replies

8. Solaris

Best guide for Jumpstart

Hi Gurus, Can you please suggest me any good guides for a Beginner to learn Solaris Jumpstart. Thank You, Rama Krishna. (2 Replies)
Discussion started by: rama krishna
2 Replies

9. Solaris

Jumpstart Solaris 10

I have a laptop and need to build an Oracle Linux kickstart server and a Solaris Jumpstart server that can build sparc and x86 systems. Is the best way to create a dual boot from grub for Oracle Linux and Solaris x86? Can the Oracle Kickstart be used as a Jumpstart to build both Solaris 10... (2 Replies)
Discussion started by: Gian
2 Replies

10. Solaris

Jumpstart Question

Hi Guys, I am little bit confused about jumpstart on solaris 10. Do you need the mac address for each system you intend to jumpstart? If you need the mac address, how will you get it? Say your server is in another location and you want to jumpstart it, how will you do it? Clarification on... (1 Reply)
Discussion started by: cjashu
1 Replies
URL(4)							   BSD Kernel Interfaces Manual 						    URL(4)

NAME
url -- Realtek RTL8150L USB Ethernet driver SYNOPSIS
url* at uhub? urlphy* at mii? DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip. The url driver supports the following adapters: CompUSA USBKR100 GreenHouse GH-USB100B Melco Inc. LUA-KTX Sitecom LN013 For more information on configuring this device, see ifconfig(8). DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8) HISTORY
The url device driver first appeared in NetBSD 1.6. AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>. BSD
September 18, 2006 BSD
All times are GMT -4. The time now is 09:05 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy