9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Is there a command that will verify what type of file system is located on a PCMCIA Card without having to mount the card? Thank you. (1 Reply)
Discussion started by: kilemark
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I keep getting an error when I insert a pcm200 card on my laptop.
The Error:
Card type 32-bit cardbus is unsupported
I am using freebsd 4.11
thanks
lucky (2 Replies)
Discussion started by: luckyarab
2 Replies
3. UNIX for Dummies Questions & Answers
Hi
I recently installed Mandrake 9 on my laptop. It has 2 PCMCIA slots, and in one of them I usually keep one of my network cards (ones an Accton 2216, the other a Surecom EP-427). Under mandrake when my computer started up (and went into runlevel 5) it attempted to start 'network' and then... (2 Replies)
Discussion started by: KrazyGuyPaul
2 Replies
4. UNIX for Dummies Questions & Answers
Hi,
I justed manged to install Solaris 8 on my Laptop, the only problem I have got is that It does not find my PCMCIA card. I need it to find my card so I can connect the Laptop to my LAN.
I am using a 3Com LAN card model number is 3CCE589ET. This card work with Linux with no problems.
... (2 Replies)
Discussion started by: chamkila
2 Replies
5. IP Networking
Hey all,
I've bought a few bits from Belkin who seem quite happy to support FreeBSD! Last time I bought a UPS from them and it's still going well :D
I saw this on their website that the 16bit PCMCIA card was supported under FreeBSD:
http://www.belkin.com/network/F5D5020.html
I went to my... (0 Replies)
Discussion started by: WIntellect
0 Replies
6. UNIX for Dummies Questions & Answers
I am using an IBM 390E laptop with a built-in LT modem which RH 7.3 does not notice. I would like to know if there are any pcmcia modems that are supported by version 7.3. If so, what is the propduct and where can I purchase it? Thanks!!
adrienb:confused: (2 Replies)
Discussion started by: adrienb
2 Replies
7. UNIX for Dummies Questions & Answers
ENV: linux Version: Mandrake 8.1, PCMCIA card: longshine lcs-8534TB.
(supported according the PCMCIA docs)
laptop is P-II lifetec
/etc/sysconfig/pcmcia:
PCMCIA=yes
PCIC=i82365 ( found via probe -m )
PCIC_OPTS="cs_irq=11 pci_irq_list=11,11 do_scan=0" ( you see i want to force irq 11 )... (3 Replies)
Discussion started by: progressdll
3 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I have a Dell Inspiron 4000 that I am using to run Redhat Linux 7.1.
This machine had 128Mb of RAM in it, and I upgraded to 512Mb.
Since this, the PCMCIA cards have disappeared from the system running under Linux, although they still work under windows and the file "/var/lib/pcmcia/stab"... (1 Reply)
Discussion started by: ghoti
1 Replies
9. UNIX for Advanced & Expert Users
We are installing a PrismII chipset wireless PCMCIA card with a new 2.4.9 linux kernel. The card is a D-Link DWL-650. The 2.4.9 kernel uses the orinoco_cs.o driver.
Anyone running this configuration?
The 2.4.9 Linux kernel has built in PCMCIA support and the README says it supports the... (1 Reply)
Discussion started by: Neo
1 Replies
XE(4) BSD Kernel Interfaces Manual XE(4)
NAME
xe -- Xircom PCMCIA Ethernet device driver
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device xe
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_xe_load="YES"
DESCRIPTION
The xe driver supports PCMCIA Ethernet adapters based on Xircom CE2- and CE3-class hardware. This includes devices made by Xircom along with
various OEM manufacturers.
Please note that the xe driver only supports PCMCIA cards and their Ethernet functions. xe does not support the on-board modem device
located on some version of the Ethernet/modem combo cards. In particular, Xircom RealPort2 cards are not supported by this driver.
The xe driver supports the following media types:
autoselect Enable autoselection of media type and options.
10Base2/BNC
Select 10Mbps operation on a BNC coaxial connector.
10BaseT/UTP
Select 10Mbps operation on a RJ-45 connector.
100BaseTX Select 100Mbps operation.
Note that 100BaseTX operation is not available on CE2-class cards, while the 10Base2/BNC mode is only available on CE2-class cards. Full-
duplex operation is currently not supported. For more information on configuring network interface devices, see ifconfig(8).
HARDWARE
The xe driver supports the following cards:
o Xircom CreditCard Ethernet (PS-CE2-10)
o Xircom CreditCard Ethernet + Modem 28 (PS-CEM-28)
o Xircom CreditCard Ethernet + Modem 33 (CEM33)
o Xircom CreditCard 10/100 (CE3, CE3B)
o Xircom CreditCard Ethernet 10/100 + Modem 56 (CEM56)
o Xircom RealPort Ethernet 10 (RE10)
o Xircom RealPort Ethernet 10/100 (RE100)
o Xircom RealPort Ethernet 10/100 + Modem 56 (REM56, REM56G)
o Accton Fast EtherCard-16 (EN2226)
o Compaq Microcom CPQ550 Ethernet/Modem PC Card
o Compaq Netelligent 10/100 PC Card (CPQ-10/100)
o Intel EtherExpress Pro/100 PC Card Mobile Adapter 16 (Pro/100 M16A)
o Intel EtherExpress Pro/100 LAN/Modem PC Card Adapter (Pro/100 M16B)
Other similar devices using the same hardware may also be supported.
DIAGNOSTICS
xe%d: Cannot allocate ioport
xe%d: Cannot allocate irq A fatal initialization error occurred while attempting to allocate system resources for the card.
xe%d: Unable to fix your %s combo card A fatal initialization error occurred while attempting to attach an Ethernet/modem combo card.
xe%d: watchdog timeout: resetting card The card failed to generate an interrupt acknowledging a transmitted packet. May indicate a PCMCIA
configuration problem.
xe%d: no carrier The card has lost all contact with the network; this usually indicates a cable problem.
SEE ALSO
pccard(4), ifconfig(8)
HISTORY
The xe driver first appeared in FreeBSD 3.3.
AUTHORS
The xe device driver was written by Scott Mitchell <rsm@FreeBSD.org>. This manual page was written by Scott Mitchell <rsm@FreeBSD.org>, and
Tom Rhodes <trhodes@FreeBSD.org>.
BUGS
Supported devices will fail to attach on some machines using the NEWCARD PC Card framework.
Automatic media selection is usually unreliable.
BSD
July 16, 2005 BSD