04-20-2004
8 More Discussions You Might Find Interesting
1. Solaris
Hi all,
i just purchased Sun Ultra Enterprise 3000,
but they did not include with keyboard/mouse .
i am very new with this box.
could you give me which type of keyboard i can use and video connector to my monitor since serial connectors for keyboard and video is different with my PC.
... (5 Replies)
Discussion started by: waterbear
5 Replies
2. Solaris
Hi,
I have a brand new SUN T5140 machine. I am trying to install Solaris 10 on the box. When I go to the machine using a KVM session I can see a blank screen , how can I get to the OK prompt to start the installation.
Thanks,
Suresh (10 Replies)
Discussion started by: gunnervarma
10 Replies
3. Solaris
Hello all
rather new to diagnosing hardware issues on SUN platforms (still new to Sol 10 also). Sorry if this is not a great question. I have searched the forums and have not found an answer to my specific issue.
Ok, I have a SUN V215 hooked up to a Thinklogical KVM extender. There are 2... (3 Replies)
Discussion started by: caddyjoe77
3 Replies
4. Hardware
Hello,
I have a sun blade 1000 machine, it passes post, has 2 750mhz sparc 3 cpus and has 4GB of ram.
I have setup a TIP connection and did everything i could to figure what the hell is going on, but I cannot it seems to me that the usb ports are not giving out any power.
I've tried all... (0 Replies)
Discussion started by: binary0x01
0 Replies
5. Solaris
Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out.
exit
rebootxscf
logout
#.
#>
#>
~#
~#
exit
sendbreak
exit
I tried to set the Mode Switch to the service... (3 Replies)
Discussion started by: aixlover
3 Replies
6. Solaris
Hi, I have a Sun Ultra 5 workstation with Sun Keyboard Type 6.
My problem is the workstation recognize the keyboard as Keyboard Type 4 instead of type 6. How can I change the workstation to recognize sun keyboard type 6. Any idea?
# kbd -t
Type 4 Sun keyboard
:wall::wall::wall: (2 Replies)
Discussion started by: fairus
2 Replies
7. UNIX for Dummies Questions & Answers
Hi, I've got a bit of a ridiculous problem and wasn't sure where to post it.
I need to use the vertical bar for piping in Bash but, as per the title, am using a UK layout on a US (physical) keyboard which doesn't have a key for it in the place I'd expect. I've tried using xbindkeys and Unicode... (7 Replies)
Discussion started by: crunchgargoyle
7 Replies
8. Solaris
I am having a problem when booting my Sun V445 machine with Solaris 10 installed on it. Machine hangs at boot at following step :
0>Copyright 2007 Sun Microsystems, Inc. All rights reserved
0>OBP->POST Call with %o0=00000800.01014000.
0>Diag level set to MAX.
0>Verbosity level set to... (21 Replies)
Discussion started by: usmanijaz101
21 Replies
URL(4) BSD Kernel Interfaces Manual URL(4)
NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8)
HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
September 18, 2006 BSD