Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Problems with network card in SCO
Operating Systems SCO Problems with network card in SCO Post 302380940 by TonyLawrence on Wednesday 16th of December 2009 05:29:28 PM
Old 12-16-2009
This sounds like you are entering values manually?

From New to SCO Unix :

"When adding a pci Network card to SCO OSR5, the card should just "pop up" with netconfig - you shouldn't get a whole list of cards to choose from. If it does not, you probably do not have the right driver and should visit ftp://ftp.sco.com/pub/drivers/ to get it. Also use "hw -r pci" to see what is actually installed."

Probably smarter to buy a card that SCO 5.0.5 DOES have drivers for. Unfortunately, that's going to be older versions - new cards may not work even if model number is the same.

Smarter still to move off SCO :-)
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

3. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

4. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies

5. SCO

3c905b network card problem with SCO 5.0.5

Hi, I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

7. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

8. SCO

network problems with sco

SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that. thanks (8 Replies)
Discussion started by: ajantha
8 Replies

9. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

LEARN ABOUT NETBSD

urlphy

URL(4)							   BSD Kernel Interfaces Manual 						    URL(4)

NAME

     url -- Realtek RTL8150L USB Ethernet driver

SYNOPSIS

     url*    at uhub?
     urlphy* at mii?

DESCRIPTION

     The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.

     The url driver supports the following adapters:

	   CompUSA USBKR100
	   GreenHouse GH-USB100B
	   Melco Inc. LUA-KTX
	   Sitecom LN013

     For more information on configuring this device, see ifconfig(8).

DIAGNOSTICS

     url%d: watchdog timeout  A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
     transmission before a timeout expired.

     url%d: no memory for rx list  The driver failed to allocate an mbuf for the receiver ring.

SEE ALSO

     arp(4), mii(4), netintro(4), usb(4), ifconfig(8)

HISTORY

     The url device driver first appeared in NetBSD 1.6.

AUTHORS

     The url driver was written by Shingo WATANABE <nabe@nabechan.org>.

BSD
								September 18, 2006							       BSD
All times are GMT -4. The time now is 06:00 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy