8 More Discussions You Might Find Interesting
1. AIX
We have an IBM Power 710. It has a USB port on the front. I have done some searching and see that there is information out there on how to create a JFS2 file system on USB drives. A few have commented that they would not recommend it, if the server is important, may crash the server... Just... (0 Replies)
Discussion started by: mbenedi
0 Replies
2. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
3. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
4. Solaris
Hi All,
I recently got a connection to the SAN through a fibre channel on my solaris box:
#luxadm -e port
/devices/pci@1d,700000/SUNW,qlc@1/fp@0,0:devctl CONNECTED
#ls -l /dev/cfg
lrwxrwxrwx 1 root root 48 Feb 23 12:31 c4 -> ../../devices/pci@1d,700000/SUNW,qlc@1/fp@0,0:fc
I then... (2 Replies)
Discussion started by: dede
2 Replies
5. Solaris
Hello all,
how can i see configured fc tapes in solaris system and how can i install a new fc shared tape device , thanks
Best Regards (2 Replies)
Discussion started by: bogacd
2 Replies
6. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
7. Solaris
I use Sunfire V480R , and i am seeing lot of scsi transport errors for the root drive & i think it is going to die . the system is having 2 drives & the second drive is kept unused . can someone guide me how do i clone the root drive to the seconddrive and make that bootable . (13 Replies)
Discussion started by: skamal4u
13 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
tms(7) Miscellaneous Information Manual tms(7)
NAME
tms - TMSCP magnetic tape interface
SYNOPSIS
For XMI/KDM on Alpha-based systems:
bus xmi0 at iop0 vector xmierror
controller uq0 at xmi? port kdm vector uqintr
device tape tms0 at uq0 drive 0
For MSI Bus: only MIPS-based DECsystem 5500
bus msi0 at ibus? vector msi_isr
controller dssc1 at msi0 msinode 1
device tape tms3 at dssc1 drive 3
For XMI/CI/HSC on Alpha-based systems:
bus xmi0 at iop0 vector xmierror
bus ci0 at xmi? port np vector cimna_isr
controller hsc6 at ci0 cinode 6
device tape tms3 at hsc6 drive 3
For tms devices dual ported between two controllers:
device tape tms2 at * drive 2
DESCRIPTION
The TMSCP driver provides a standard tape drive interface, as described in mtio(7). This is a driver for any controller that adheres to
the Tape Mass Storage Control Protocol (TMSCP). The TMSCP controllers communicate with the host through a packet-oriented protocol termed
the Tape Mass Storage Control Protocol.
Tape Support - Alpha-based systems
TA78, TA79, TA81, TA90, TA90E, TA91
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
FILES
/dev/rmt???
/dev/nrmt???
SEE ALSO
mtio(7), MAKEDEV(8), uerf(8), tapex(8) delim off
tms(7)