10 More Discussions You Might Find Interesting
1. Linux
Hi,
Can someone guide me regarding how to connect to internet.
what are steps?
Thanks in advance (2 Replies)
Discussion started by: naren nandale
2 Replies
2. Solaris
Dear freinds...
I downloaded solaris for x86 and was able to configure the lan correctly.. I can ping and share with other destops through lan... but still I can't connect to internet ? can you please help..
I put my default gateway which is 192.168.1.1 to /etc/defaultrouter but with no use..... (13 Replies)
Discussion started by: yahyaaa
13 Replies
3. Linux
HI,
Am using GPRS ( MOB # 3230 ) internet connection in windows
Hw to use internet r connect in linux.. ( Red Hat Linux Ver.10 )
Please help me..
Thanks in adv.. (1 Reply)
Discussion started by: bharath raja
1 Replies
4. Solaris
Hi I installed solaris developer edition 1/08 today.I want to connect to Broadband internet through my ADSL 2+ Modem/Router with a username and password.
plz help in this case,I am new to sun solaris:confused:
the modem itself is a router it worked well on ubuntu and red hat (3 Replies)
Discussion started by: santugvd
3 Replies
5. Solaris
i have just installed solaris 10 on a 60 gb hard drive. now im trying to install my nic driver but when i put in the floppy disk for the nic card it cant read it, so then i found that i have to mount the floppy drive and i tried putting in the mount command but i dont know where to mount it and if... (38 Replies)
Discussion started by: vutty81
38 Replies
6. Solaris
ive installed a fresh copy of solaris 10 on a E3500 Server machine, i gave it a static IP address , 192.168.1.15 its a test server in our office (small office) we are using LINKSYS as our internet router and DHCP as well .. its IP is 192.168.1.1 and ive added this IP as Default route on the server... (9 Replies)
Discussion started by: mduweik
9 Replies
7. UNIX for Dummies Questions & Answers
I running HPUX 11.0,
Netscape gives me an error "Unable to locate Server" when using a www.something.com address.
If I use an IP address I get past the router and onto the Internet.
My workstation can get to the Router @ 192.168.0.1 and also it's local APACHE server.
I have DHCP enabled... (8 Replies)
Discussion started by: johnalt
8 Replies
8. Shell Programming and Scripting
I wonder how I shall read the result below, especially 'what'
shown below.
The result was shown when I entered 'w'.
E.g what is TOP? What is gosh ( what does selmgr mean?)?
login@ idle JCPU PCPU what
6:15am 7:04 39 39 TOP
6:34am 6:45 45 45 TOP
6:41am ... (1 Reply)
Discussion started by: Aelgen
1 Replies
9. UNIX for Dummies Questions & Answers
for those who have read my earlier posts i have been trying for about a week and a half to get my internet connection working with no results...
my isp is ex-pressnet (in VA)...one-way cable internet service (dial-up for uploads, cable for downloads) using a com21 cable modem...this is extremly... (6 Replies)
Discussion started by: justchillin
6 Replies
10. UNIX for Dummies Questions & Answers
hello :(
i have just installed linux mandrake 7.1 and i've been trying to get help EVERYWHERE!! i can't get on the internet.
it dials the modem and connects but when i try and go 2 any web pages it gets no further than looking for the server.
plleeeeeeeeeeeeeeeeeeeeeease help
thanks,... (7 Replies)
Discussion started by: mipsy
7 Replies
UPSCMD(8) NUT Manual UPSCMD(8)
NAME
upscmd - UPS administration program for instant commands
SYNOPSIS
upscmd -h
upscmd -l ups
upscmd [-u username] [-p password] ups command
DESCRIPTION
upscmd allows you to invoke "instant commands" in your UPS hardware. Not all hardware supports this, so check the list with -l to see if
anything will work on your equipment.
On hardware that supports it, you can use this program to start and stop battery tests, invoke a front panel test (beep!), turn the load on
or off, and more.
OPTIONS
-h
Display the help message.
-l ups
Show the list of supported instant commands on that UPS. Some hardware may not support any of them.
-u username
Set the username for the connection to the server. This is optional, and you will be prompted for this when invoking a command if -u is
not used.
-p password
Set the password to authenticate to the server. This is also optional like -u, and you will be prompted for it if necessary.
ups
Connect to this UPS. The format is upsname[@hostname[:port]]. The default hostname is "localhost".
UNATTENDED MODE
If you run this program inside a shell script or similar to invoke a command, you will need to specify all of the information on the
command line. This means using -u and -p. Otherwise it will put up a prompt and your program will hang.
This is not necessary when displaying the list, as the username and password are not required for read-only mode.
DANGEROUS COMMANDS
Some drivers like apcsmart(8) have built-in paranoia for the dangerous commands like load.off. To make them actually turn off the load, you
will have to send the command twice within a short window. That is, you will have to send it once, then send it again after 3 seconds
elapse but before 15 seconds pass.
This paranoia is entirely defined within the driver. upsd and upscmd have no control over the timing.
DIAGNOSTICS
upscmd won't work unless you provide a valid username and password. If you get "access denied" errors, make sure that your upsd.users(5)
has an entry for you, and that the username you are using has permissions to SET variables.
BUGS
There is currently no way to tell the user when the driver requires confirmation to invoke a command such as load.off. Similarly, there is
not yet a way to tell the user if a command succeeds or fails.
This is on the list of things to fix in the future, so don't despair. It involves magic cookies.
SEE ALSO
upsd(8), upsrw(8)
INTERNET RESOURCES
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 UPSCMD(8)