8 More Discussions You Might Find Interesting
1. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
2. UNIX for Dummies Questions & Answers
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
3. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
4. SCO
Dear All,
I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as... (4 Replies)
Discussion started by: njoroge
4 Replies
5. AIX
Hello everyone
I have a problem with one of my drives in an aix box. The library is a 3583 and Aix is 5.3 TL9
The problem was that the fibre channel not work and I change the fibre but when I logging to the aix box I got this in the rmt3
lsdev | grep rmt
rmt0 Available 03-08-00-6,0... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies
6. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
8. AIX
Hello all,
I have just installed an HP dat72 external tape drive to an IBM 275 Intellistation (AIX 5L). It was installed as an Other SCSI Tape Drive (rmt1). I am using the Web Based System Manager at this point to do an initial backup
of a journaled file system. I am getting an error and am... (1 Reply)
Discussion started by: joeweisser
1 Replies
HT(4) Kernel Interfaces Manual HT(4)
NAME
ht - TM-03/TE-16,TU-45,TU-77 MASSBUS magtape interface
SYNOPSIS
/sys/conf/SYSTEM:
NHT ht_drives # TE16, TU45, TU77
/etc/dtab:
#Name Unit# Addr Vector Br Handler(s) # Comments
ht ? 172440 224 5 htintr # tu 16 massbus tape
major device number(s):
raw: 6
block: 0
minor device encoding:
bits 0003 specify HT drive
bit 0004 specifies no-rewind operation
bit 0010 specifies 1600BPI recording density instead of 800BPI
DESCRIPTION
The tm-03/transport combination provides a standard tape drive interface as described in mtio(4). All drives provide both 800 and 1600
bpi; the TE-16 runs at 45 ips, the TU-45 at 75 ips, while the TU-77 runs at 125 ips and autoloads tapes.
FILES
/dev/MAKEDEV script to create special files
/dev/MAKEDEV.local script to localize special files
SEE ALSO
mt(1), tar(1), tp(1), mtio(4), tm(4), ts(4), dtab(5), autoconfig(8)
DIAGNOSTICS
tu%d: no write ring. An attempt was made to write on the tape drive when no write ring was present; this message is written on the termi-
nal of the user who tried to access the tape.
tu%d: not online. An attempt was made to access the tape while it was offline; this message is written on the terminal of the user who
tried to access the tape.
tu%d: can't change density in mid-tape. An attempt was made to write on a tape at a different density than is already recorded on the
tape. This message is written on the terminal of the user who tried to switch the density.
tu%d: hard error bn%d er=%b ds=%b. A tape error occurred at block bn; the ht error register and drive status register are printed in
octal with the bits symbolically decoded. Any error is fatal on non-raw tape; when possible the driver will have retried the operation
which failed several times before reporting the error.
BUGS
If any non-data error is encountered on non-raw tape, it refuses to do anything more until closed.
The system should remember which controlling terminal has the tape drive open and write error messages to that terminal rather than on the
console.
3rd Berkeley Distribution January 28, 1988 HT(4)
