10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Greeting All
Diag tool HDD clone SCO 5 + Oracle 7 DB ( IBM T30 )
I am new to this forum and my knowledge on computers OS is average .
I have just acquired a factory diag tool for BMW/RR/MINI from a retired mechanic. Its runs on a IBM T30 laptop with a Unix/Oracle DB system. Sco 5... (8 Replies)
Discussion started by: bmw635
8 Replies
2. SCO
Hi all
I have read about mounting crashed HDD from a sco system in this forum. However this I received an image on raw format of the crashed system that was using an IDE HDD. Which method should I mount my image? IDE scsi or USB? The image is stores in an external connected through USB .
Also... (4 Replies)
Discussion started by: OrangeKenny
4 Replies
3. Solaris
Dear All,
I have been trying to move my existing Solaris Installation (x86, 10/08) to a bigger HDD.
So I created a 22 cylinder boot partition and used the rest of the space for a Solaris2 partition. Then I created slices same size like on my current disk.
I copied all files with cpio and... (3 Replies)
Discussion started by: BigT79
3 Replies
4. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
5. Solaris
All,
I am a complete grasshopper when it comes to Unix, so here goes. I have a Solaris 9 server, running two 36GB HDD in a mirrored configuration. I am running low on disk space, and have purchased an additional 145GB HDD. Can anyone point me in the direction to some documentation on how to... (1 Reply)
Discussion started by: ptvenom427
1 Replies
6. SCO
Hi guys,
I have this problem ,
One of our client's hdd went down and we cannot boot up the machine , I've installed a new hdd with a fresh copy of SCO 5.0.6 same as the one in the old HDD, i think the data still good in the old HDD.
My question!!!
How can i access the data from the fresh... (4 Replies)
Discussion started by: josramon
4 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
I need some advice on dual booting a dell box so that I can have WinXP and Solaris 10 OS there. The question is, what is the best way of preparing the hdd for prior to installation?
I have used created two partition, one for xp and the and the other unallocated partition for Solaris.... (3 Replies)
Discussion started by: S0laris_B0y
3 Replies
8. SCO
Hi guys,
I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this.
I'm not using any raid, just one HDD.
Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies
9. Shell Programming and Scripting
Hi Engg. ! :mad:
I have a harddisk on which SCO UNIX Open Server was installed. There was some data (in .dbf format) on it. Present condition of HDD is that it is not booting. Now I want to mount this HDD through other HDD on which SCO UNIX Open Server is installed by attaching... (0 Replies)
Discussion started by: Niraj Gopal Sha
0 Replies
10. UNIX for Advanced & Expert Users
HI ALL,
I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
mknod(1), chown(1), mount(8), sd(4)
Linux 1992-12-17 HD(4)